|
CX-One 4.1
The following changes have been made to the programs included in CX-One 4.1 and CX-One Lite 4.1:
|
|
 |
Tip: To subscribe to this article so that you get notified of any changes click the "Subscribe" button above.
|
| Program |
Version |
In CX–One Full |
In CX–One Lite |
Changes |
| CX-Programmer |
9.20 |
 |
♦ |
*Can use structure symbols in ST.
*Can use timer and counter symbols in ST.
*Can use the following ten functions in ST:
MOD (remainder), SHL (left bit shift), SHR (right bit shift), ROL (left bit rotation), ROR (right bit rotation), LIMIT (upper and lower limit control), SEL (data selection), MUX (data extraction), MAX (max search) and MIN (min search).
*Can copy and paste network tag structure symbols to CX-Designer (V3.20 and higher). (CJ2 PLC)
*Solved the problem that prevented cursor movement after using the F3 key for continuous searches.
*Solved the problem that caused a program error on PLC when the SETB instruction was used in FB ladder program and the program was transferred to PLC.
*Solved the problem that caused GPF at existing CXProgrammer when a project to which automatic memory allocation was set. |
| CX-Integrator |
2.43 |
|
|
*Updated the device vender name displayed in the DeviceNet Component list. |
| CX-Designer |
3.20 |
|
|
*Can copy and paste network tag structure symbols from CX-Programmer (V9.20 and higher). (CJ2 PLC)
*Solved the problem that prevented transfer of a project whose size is over 20 MB on NS5-[][]1[][]-V2, NSH5-[][][]1[][]-V2 and NSJ5-[][]1[][]-[][][]. |
| CX-Simulator |
1.98 |
|
|
* Solved the problem that could not display present values correctly on a program that uses function block input and output symbols. |
| CX-Server |
4.5.4.5 |
|
|
*Can reflect the range check in accordance with the Axis Parameter setting to Memory Operation Sequence Data on Position Control Unit (CJ1W-NC[]81 and CJ1W-NC[]82) Setting Component.
[CPS]
*Added the following file:
CPS_CJ2M-EIP21_Ver2_1.xml
[Support of New Types]
*Supported the built-in EIP Unit version 2.1 of CJ2M-CPU3[].
*Supported the G5-series Servo Drive (EtherCAT communication type R88D-KN[]-ECT (the model without "-R")) which would be released shortly. On Position Control Unit (CJ1W-NC[]81 and CJ1W-NC[]82) Setting Component, the model R88D-KN[]-ECT-R is described as Ver.1.0 while the model R88D-KN[]-ECT (the model without "-R") as Ver.2.0.
*Solved the problem that disturbed error occurrence even if a Unit total power consumption exceeded the allowable consumption for a power supply.(CS/CJ PLC)
*Can transfer projects created by a previous version of Position Control Unit (CJ1W-NC[]81 and CJ1W-NC[]82) Setting Component on the new version, which was previously impossible.
*Solved the problem that the Axis Parameter editing screen could not start up when an out-of-range Axis Parameter was set on Position Control Unit (CJ1W-NC[]81 and CJ1WNC[] 82) Setting Component.
*Solved the problem that the Axis Parameter editing screen could not start up when an out-of-range Axis Parameter was set on Position Control Unit (CJ1W-NC[][]4) Setting Component.
*Enhanced the recovery function from communications errors at USB connection.
|
| CX-Thermo |
4.20 |
|
|
No changes |
| CX-Drive |
2.20 |
|
|
[Support of New Type]
*Supported the G5-series Servo Drive (EtherCAT communication type R88D-KN[]-ECT (the model without "-R")) which would be released shortly. On CX-Drive, the model R88D-KN[]-ECT-R is described as Ver.1.0 while the model R88D-KN[]-ECT (the model without "-R") as Ver.2.0.
*Supported 3G3MX2 DeviceNet option board interface(3G3AX-MX2-DRT).
*Improved the parameter transferring speed for G5 servo driver(R88D-KN[]-ECT Ver.2.0 or later).
|
| Switch Box |
1.66 |
|
|
No changes |
| Network Configurator |
3.21 |
|
|
[Support of New Types]
*Supported for the built-in EIP Unit version 2.1 of CJ2MCPU3[] that allows tag data link of a maximum of 640CH. |
| CX-ConfiguratorFDT |
1.2.2.2 |
|
|
*Supported Timeout Setting on CompoNet Master DTM. |
| CX-Sensor |
1.21 |
|
|
No changes |
| CX-Motion Pro |
1.2.1 |
|
|
No changes |
| CX-Position |
2.51 |
|
|
No changes |
| CX-Protocol |
1.91 |
|
|
No changes |
| CX-Process Tool |
5.24 |
|
|
No changes |
| Face Plate Auto-Builder |
3.11 |
|
|
No changes |
| CX-FLnet |
1.00 |
|
|
No changes |
| CX-Motion |
2.35 |
|
|
No changes |
| CX-Motion-NCF |
1.91 |
|
|
No changes |
| CX-Motion-MCH |
2.24 |
|
|
No changes |
♦ CX-One Lite includes CX-Programmer Junior for CP1L, CP1H, CPM1, CPM1A, CPM2A, CPM2C and SRM1 PLCs only.
CX-One 4.1 is available as a DVD for new customers or via CX-One Autoupdate for CX-One 4.0 customers.
CX-One 4.0
The following changes have been made to the programs included in CX-One 4.0 and CX-One Lite 4.0:
♦ CX-One Lite includes CX-Programmer Junior for CP1L, CP1H, CPM1, CPM1A, CPM2A, CPM2C and SRM1 PLCs only.
CX-One 4.0 is a major update and available as a DVD.
CX-One 3.1
The following changes have been made to the programs included in CX-One 3.1 and CX-One Lite 3.1:
♦ CX-One Lite includes CX-Programmer Junior for CP1L, CP1H, CPM1, CPM1A, CPM2A, CPM2C and SRM1 PLCs only.
CX-One 3.1 is available as a DVD for new customers or via CX-One Autoupdate for CX-One 3.0 customers.
See Also