This switch comes in the same shape as Omron Z basic switches except in pin-plunger position, yet endures inrush currents as large as 75A. General-purpose basic switch High-capacity switch capable of handling 20A loads Endures inrush currents as large as 75A IP00

These subassembled pushbutton switches have a modular construction: pushbutton + case + lamp (if applicable) + switch. A16 is a nut-mounted pushbutton switch with a short mounting depth of less than 28.5mm below panel. Wide variety of control and signal devices: lighted, non-lighted and buzzer Quick and easy assembly, snap-in switch Wide range of switching capacity from standard load to micro load High reliability, IP65 UL, cUL and CSA approved, conforms to EN60947-5-1 and IEC947-5-1

The A165E line-up offers E-Stop switches with various head types. For flexible application, a wide range of accessories is provided. To set up easy installation and maintenance, various contact combinations are available. Direct opening mechanism with minimum contact separation of 3mm Safety lock mechanism prevents misuse Short mounting depth Modular construction; easy installation using snap-in switch

A165K nut-mounted, key-type selector switches have a modular construction and a short mounting depth of less than 28.5mm below the panel. They come in a wide range of switching capacities, from standard load to micro load. Momentary and latching models available Automatic and manual models available Modular construction, snap-in switch unit Oil-resistant IP65 models UL and cUL approved, conforms to EN60947-5-1 and IEC947-5-1

A165S/W nut-mounted, knob-type selector switches have a modular construction and a short mounting depth of less than 28.5mm below the panel. They come in a wide range of switching capacities, from standard load to micro load. Lighted and non-lighted models available Automatic and manual models available Modular construction, snap-in switch unit Oil-resistant IP65 models UL and cUL approved, conforms to EN60947-5-1 and IEC947-5-1

A16_-P panel-/PCB-switches are similar to A16, but with PCB terminals. A lever enables easy mounting and removal of the socket. Separable types greatly reduce installation time. The hold status can easily be checked from the rear of the PCB. Panel-/PCB-mounted pushbutton switch 16mm diameter improves operating efficiency Enables many combinations of operating parts with the extensive A16 series line-up Achieves large reduction in wiring work by placing operating switches on boards Helps standardise operating sections and prevent wiring errors

A22 comes in a wide variety of shapes and colours and is installable in 22-dia. or 25-dia. panel cutouts. The switch unit can easily be mounted. A22 is mounted using either open-type (fork-type) or closed-type (round-type) crimp terminals. Finger-protection mechanism on switch unit provided as standard feature Increased wiring efficiency with three-row mounting of switch blocks IP65 oil-resistant (non-lighted models), IP65 (lighted models) Lighted and non-lighted, flat, projection and half- and full-guard versions EN60947-5-1, UL and cUL approved

The A22E line-up offers E-Stop switches with various head types. For flexible application, a wide range of accessories is provided. To set up easy installation and maintenance, various contact combinations are available. Direct opening mechanism with minimum contact separation of 3mm Safety lock mechanism prevents misuse Easy mounting of switch blocks Round, forked crimp terminals or ferrules can be used for installation

These nut-mounted, key-type selector switches can be installed in a 22-dia. or 25-dia. panel cutout. Mounting and removal of the switch unit is easy due to the modular construction of the A22K. The three-row mounting of switch blocks (up to six contacts) increases the wiring efficiency. Finger-protection mechanism on switch unit provided as standard feature Mounted using open-type (fork) or closed-type (round) crimp terminals IP65 oil-resistant UL and cUL approved and conforms to EN60947-5-1 Available with 2- and 3-notch selector with or without spring return

These nut-mounted, key-type selector switches can be installed in a 22-dia. or 25-dia. panel cutout. Mounting and removal of the switch unit is easy due to the modular construction of the A22K. The three-row mounting of switch blocks (up to six contacts) increases the wiring efficiency. Finger-protection mechanism on switch unit provided as standard feature Mounted using open-type (fork) or closed-type (round) crimp terminals IP65 oil-resistant (non-lighted models), IP65 (lighted models) UL and cUL approved and conforms to EN60947-5-1 Available with 2- and 3-notch selector with or without spring return

The A4E enabling switch provides two or four outputs. For harsh environments, it can be provided with a rubber cover. Various mounting possibilities guarantee easy integration in hand-held devices. Feedback by mechanical "click" Variable mounting Types for harsh environments are available

The NS-Series is our advanced HMI series that covers a large range from 5.7" Monochrome STN to 12.1" TFT. Easily programmed with a single piece of software, it offers advanced faetures, many communication possibilities, incuding Ethernet, very good synergy with our PLCs and devices, an extremely flat design and a backlight life of up to 75,000 hours.