The 61F-D21T is a conductive level controller in a 22.5mm-wide industrial housing. Via DIP switches its function (supply or drainage) can be selected. This product is for single- or two-point level control. Time delay function up to 10s Supply voltages: 24VAC/115VAC/220 to 230VAC Control output: relay 6A at 250VAC resistive load Probes cable length: max. 100m from controller LED indicator: green for power ON, yellow for output relay

The 61F-GP-N8 can be used for single- or two-point level control of conductive materials, both liquids and solids. These products are equipped with a red LED operation indicator. Low-voltage (AC) electrodes (8VAC or 24VAC) Operation range: 4-15kΩ, 70-300kΩ Detection method: conductive Probes need to be ordered separately Conforms to EMC and LVD directives, UL/CSA approved

This controller is for single- or two-point level control. 24VDC supply allows for usage in locations without AC power supply. Relay contact chattering usually caused by waves has been eliminated by using open collector output, reducing contact wear. Adjustable sensitivity: operation range: 0-100kΩ Red LED for operation indicator Conforms to EMC and LVD directives UL/CSA approved Probes need to be ordered separately

This switch comes in the same shape as Omron Z basic switches except in pin-plunger position, yet endures inrush currents as large as 75A. General-purpose basic switch High-capacity switch capable of handling 20A loads Endures inrush currents as large as 75A IP00

These subassembled pushbutton switches have a modular construction: pushbutton + case + lamp (if applicable) + switch. A16 is a nut-mounted pushbutton switch with a short mounting depth of less than 28.5mm below panel. Wide variety of control and signal devices: lighted, non-lighted and buzzer Quick and easy assembly, snap-in switch Wide range of switching capacity from standard load to micro load High reliability, IP65 UL, cUL and CSA approved, conforms to EN60947-5-1 and IEC947-5-1

The A165E line-up offers E-Stop switches with various head types. For flexible application, a wide range of accessories is provided. To set up easy installation and maintenance, various contact combinations are available. Direct opening mechanism with minimum contact separation of 3mm Safety lock mechanism prevents misuse Short mounting depth Modular construction; easy installation using snap-in switch

A165K nut-mounted, key-type selector switches have a modular construction and a short mounting depth of less than 28.5mm below the panel. They come in a wide range of switching capacities, from standard load to micro load. Momentary and latching models available Automatic and manual models available Modular construction, snap-in switch unit Oil-resistant IP65 models UL and cUL approved, conforms to EN60947-5-1 and IEC947-5-1

A165S/W nut-mounted, knob-type selector switches have a modular construction and a short mounting depth of less than 28.5mm below the panel. They come in a wide range of switching capacities, from standard load to micro load. Lighted and non-lighted models available Automatic and manual models available Modular construction, snap-in switch unit Oil-resistant IP65 models UL and cUL approved, conforms to EN60947-5-1 and IEC947-5-1

A16_-P panel-/PCB-switches are similar to A16, but with PCB terminals. A lever enables easy mounting and removal of the socket. Separable types greatly reduce installation time. The hold status can easily be checked from the rear of the PCB. Panel-/PCB-mounted pushbutton switch 16mm diameter improves operating efficiency Enables many combinations of operating parts with the extensive A16 series line-up Achieves large reduction in wiring work by placing operating switches on boards Helps standardise operating sections and prevent wiring errors

A22 comes in a wide variety of shapes and colours and is installable in 22-dia. or 25-dia. panel cutouts. The switch unit can easily be mounted. A22 is mounted using either open-type (fork-type) or closed-type (round-type) crimp terminals. Finger-protection mechanism on switch unit provided as standard feature Increased wiring efficiency with three-row mounting of switch blocks IP65 oil-resistant (non-lighted models), IP65 (lighted models) Lighted and non-lighted, flat, projection and half- and full-guard versions EN60947-5-1, UL and cUL approved

The A22E line-up offers E-Stop switches with various head types. For flexible application, a wide range of accessories is provided. To set up easy installation and maintenance, various contact combinations are available. Direct opening mechanism with minimum contact separation of 3mm Safety lock mechanism prevents misuse Easy mounting of switch blocks Round, forked crimp terminals or ferrules can be used for installation

These nut-mounted, key-type selector switches can be installed in a 22-dia. or 25-dia. panel cutout. Mounting and removal of the switch unit is easy due to the modular construction of the A22K. The three-row mounting of switch blocks (up to six contacts) increases the wiring efficiency. Finger-protection mechanism on switch unit provided as standard feature Mounted using open-type (fork) or closed-type (round) crimp terminals IP65 oil-resistant UL and cUL approved and conforms to EN60947-5-1 Available with 2- and 3-notch selector with or without spring return

These nut-mounted, key-type selector switches can be installed in a 22-dia. or 25-dia. panel cutout. Mounting and removal of the switch unit is easy due to the modular construction of the A22K. The three-row mounting of switch blocks (up to six contacts) increases the wiring efficiency. Finger-protection mechanism on switch unit provided as standard feature Mounted using open-type (fork) or closed-type (round) crimp terminals IP65 oil-resistant (non-lighted models), IP65 (lighted models) UL and cUL approved and conforms to EN60947-5-1 Available with 2- and 3-notch selector with or without spring return

The A4E enabling switch provides two or four outputs. For harsh environments, it can be provided with a rubber cover. Various mounting possibilities guarantee easy integration in hand-held devices. Feedback by mechanical "click" Variable mounting Types for harsh environments are available

The NS-Series is our advanced HMI series that covers a large range from 5.7" Monochrome STN to 12.1" TFT. Easily programmed with a single piece of software, it offers advanced faetures, many communication possibilities, incuding Ethernet, very good synergy with our PLCs and devices, an extremely flat design and a backlight life of up to 75,000 hours.

The NT Series is ideal for applications where basic touch screens are required. It is available in monochrome screens of up to 5.7 inch. It comes standards in a rugged IP65 housing. The aim of these HMIs is smaller machines with less advanced features and lower costs.

CASE is a special software that provides solutions for customised applications. It gives a standard inverter the performance of a custom-made solution, allowing huge savings in hardware and increasing the overall system reliability.

CelciuXº is designed to handle complex temperature profiles thanks to Omron’s unique Gradient temperature Control (GTC) algorithm and to offer easy program-less communication with Omron and third-party PLCs and HMI. Above all, CelciuXº incorporates all “simple to use” clever temperature control technology, like 2-PID, disturbance control and various ways of tuning. Interfaces to a wide range of industrial networks Reduced engineering due to Programm-less communications, Smart Active Parts and Function Block Libraries Available with screw terminals and screw-less clamp terminals One unit handling various types of input, such as Pt, Thermocouple, mA, and V input Gradient Temperature Control

Abreviation for 'CompactFlash': type of memory card

Compact modular CJ1G and CJ1H PLCs offer the highest performance per volume in its class. See Product Info

The smallest members of the modular CJ1 family. See Product Info

New technology modular PLC family

Compact remote I/O units combine a fixed number of I/O points in a space saving 1P20 housing. Built-in smart monitoring functions for voltage level, broken wire, actuator and cycle time will assist in planning preventive maintenance for machines and eliminating costly downtime. Smart slaves are available for the open DeviceNet and CompoNet networks.

CP Series Compact PLCs, with integrated power supply and in- and outputs, range from the simple non expandable 10-point CPM1A controller, to the powerful CP1H. Equipped with a large instruction set to allow efficient programming, these controllers are ideal for small machine control. With their built-in high speed counter functions and pulse outputs, simple positioning or speed control applications can be handled with ease.

Compact micro-PLC with built-in high-speed counters and pulse outputs are ideal for multi-axis positioning control. See Product Info

The compact micro-PLC machine controller with 14, 20, 30, or 40 I/O built-in. See Product Info

Setting a standard for micro PLCs, the CPM1A packs all basic functions into a compact size. Four CPU sizes are available, each with a choice of AC or DC power, relay or transistor outputs. Select any combination of power supply, output, and the number of I/O points to meet your needs

Every CPM2A CPU comes equipped with an RS-232C interface as standard, e.g. to provide easy connection to a Programmable Terminal for fast and easy machine monitoring, setpoint adjustment, etc. Simple positioning with the pulse I/O function is another example of the many advanced functions and high added value that the CPM2A brings to compact machines. Removable terminal blocks ensure easy maintenance, and the CPM2A uses the same expansion I/O Units as the CPM1A for easy and economical sharing of system components.

The versatile slim-line controller. An extensive range of models ensures efficient machine control in an ultra-compact package. CPU Units are available with relay or transistor output, terminal block or various connector options, and an optional real-time clock function. Select the output type, number of I/O points and other specifications to meet your needs. Expansion I/O Units with 8 to 32 I/O points make it possible to configure a control system with a maximum of 192 I/O points.

A clear demonstration of how OMRON designs its PLC systems for a long life and guaranteed availability over an extensive period. The first CQM1 PLCs were released in 1993. The products you can buy today are more powerful and flexible, but still compatible with all early I/O units. Even the latest programming tools support the older models. All OMRON PLCs are a solid investment.

The Crane Application Software is the Omron-Yaskawa dedicated solution for Cranes applications. It customises the F7 inverter high-performance features to the specific software and hardware needs of Crane applications. Smooth operation thanks to jerk-control capabilities High motor torque and speed accuracy even at low speed Dedicated brake sequence and specific safety functionality Flexible overload/over-torque detections Load holding operation using "zero servo" function Varispeed F7 supported inverter

Combining the smart features of DRT2 DeviceNet I/O and the speed and ease of use of CompoBus/S, CompoNet is ideal for high-speed machine control with a flexible and expandable architecture. The special flat cable and IDC connectors make installation quick and easy. The use of repeaters allows wide-area networks with free topology, ideal for conveyor- and warehouse automation.

IP67 I/O offers a high degree of protection, but requires costly connection technology. CompoNet IP54 I/O offers an alternative with standard I/O connections, easy communication wiring with IDC connectors, all in a dust-proof and splash-resistant case. High-speed communication and flexible topology make it ideal for finely distributed control.

Omron's most extensive PLC family with a maximum capacity of 5120 'local' digital I/Os and extensive expansion units. See Product info

The Omron CS1W-CIF31 is a USB to serial conversion cable sold as an accessory to PLCs like CJ1M, CJ1G/H, CS1 etc to allow a PC with only USB ports to communicate via serial to PLCs.

Software package for writing runtime communication with controllers.

One Software package for configuration and programming of all Automation products. See the Product Page on our sales web site for more info.

Software for writing runtime communication with devices using CX-Server. See the Product Page on our sales web site for more info.

Software for connecting third party/multivendor software to Omron devices using CX-Server. See the Product Page on our sales web site for more info.

Virtual PLC for simulation and debugging of CS, CJ and CP PLCs. See Product info

PC based runtime HMI and supervisory software. See the Product Page on our sales website for more info.

D4A-_N has a double seal on the head and a complete gasket cover to ensure a better seal. The housing has been improved to ensure greater shock resistance. Models with fluoro-rubber are available for use in chemical applications. Wide standard operating temperature range: -40°C to 100°C (standard) Block mounting method reduces weight to 260g Block mounting method also reduces downtime for maintenance Meets UL NEMA 3, 4, 4X, 6P, 12 and 13 Immersion-proof IP67

The D4BL guard-lock safety-door switches are available with three built-in contacts. They are mechanically locked when the key is inserted and have a solenoid release. An auxiliary release key ensures easy maintenance and unlocks the door in case of power failure. Automatically mechanical lock Auxiliary release key for easy maintenance Tough aluminium die-cast body Horizontal and vertical conduit opening Head direction can easily be changed

The D4BN family is a complete line-up of safety-limit switches in metal housing. They are available with two built-in contacts and a wide range of head and actuator types. To set up easy installation and maintenance, various conduit types, e.g. M20, are provided. Direct opening mechanism Various actuators Robust metal housing Gold-plated contacts for handling micro loads Metric conduit types available

The D4BS line-up includes two-contact models with 1NC/1NO and 2NC in a robust metal housing. 1 or 3 conduit openings, such as M20 or PG13,5 are available. Robust metal housing Line-up with two contacts: 1NC/1NO and 2NC Standardised gold-clad contacts for high contact reliability Applicable for standard loads and micro loads

The D4C range of switches offers a wide choice of actuators. All switches are liquid and dust resistant, conforming to IEC IP67. Various types are available: pre-wired, low temperature, viscosity resistant, etc. Enclosed miniature limit switch, only 16mm-thick Metal housing with triple-sealed construction LED indicator for easy monitoring Ganged mounting for multiple switching Mechanical life expectancy = 10 million, switching/min = 30

The D4CC family of limit switches comes as standard with a triple-seal construction (IP67), cable connectors for easy switch replacement and an operation indicator for easy monitoring. Miniature limit switch Various models including roller lever Switches are only 16mm-thick with connector Cable connectors for easy switch replacement Immersion proof; IEC IP67, UL and CSA (type 3, 4 and 13)

D4E-_N comes with flat springs that improve the lever ratio of the built-in switch, ensuring smooth snap action and long life expectancy. Its one-touch connector eliminates the need for tedious wiring operations and reduces downtime. Protection cover protects the built-in switch from dust and oil Plunger incorporates a tough, long-lasting seal cap Minute load model with gold cladding is optimal for electronic control IP67

The D4GL guard-lock safety-door switches are available with four or five built-in contacts. When locked, they have a key holding force of up to 1000N. Mechanical lock/solenoid release types and vice versa set up the complete range in combination with various conduit types, e.g. M20. Slim safety-door switch with electromagnetic lock or unlock mechanism Models with four or five built-in contacts Strong key holding force: 1000N For standard loads and micro loads Keys are compatible with D4NL and D4NS

The D4GS line-up includes two- and three-contact models with various contact configurations. D4GS safety-door switches have a cable connection with a length of 1m, 3m or 5m. Slim housing only 17mm wide Line up with up to three contacts: 1NC/1NO, 2NC, 2NC/1NO and 3NC Reversible design allows front or rear mounting Key operation hole with rubber mounting to absorb vibration and shock

D4MC provides users with high precision and a long life (10,000,000 mechanical operations). It is sealed with a gasket diaphragm without use of any adhesive or pin, making it suitable for applications demanding higher mechanical strength and for dust-proof and drip-proof applications. Various models, plungers and levers available Panel-mount versions have the same operating position as the Z basic switch IP67, UL, CSA

The D4N-family is a complete line-up of safety-limit switches. They are available with one, two or three built-in contacts and a wide range of head and actuator types. To set up easy installation and maintenance, various conduit types, e.g. M20 and M12 connector types, are provided. Direct opening mechanism Various actuators Double insulation Gold-plated contacts for handling micro loads Metric conduit types available

D4NH safety-door hinge switches are available with one or two built-in contacts, shaft or arm lever actuator and various conduit types, e.g. M20. Direct opening mechanism Shaft or arm lever actuator Wide temperature range Metric conduit and M12 connector types are available

The D4NL guard-lock safety-door switches are available with four or five built-in contacts. When locked, they have a key holding force of up to 1300N. Mechanical lock/solenoid release types and vice versa set up the complete range in combination with various conduit types, e.g. M20. Safety-door switch with electromagnetic lock or unlock mechanism Models with four or five built-in contacts Strong key holding force: 1300N For standard loads and micro loads Keys are compatible with D4GL and D4NS

The D4NR family is a complete line-up of safety-limit switches with manual reset. They are available with one, two or three built-in contacts and a wide range of actuator types. To set up easy installation and maintenance, various conduit types, e.g. M20 and M12 connector types, are provided. Direct opening mechanism Various actuators Pull-reset switches Gold-plated contacts for handling micro loads Metric conduit types available

The D4NS line-up includes three-contact models with 2NC/1NC and 3NC contact forms in addition to the previous contact forms, 1NC/1NO and 2NC. Models with M12 connectors and conduit opening, such as M20, are also available. Line-up with three contacts: 2NC/1NC and 3NC contact forms Line-up with two contacts 1NC/1NO and 2NC M12 connector types available Standardised gold-clad contacts for high contact reliability Applicable for standard loads and micro loads

This switch is ideal for detecting and measuring wear of cutting tools or for original point of work. Available types have built-in operation, with fibre optic remote operation indicator or with screw-type cable connector for easy installation and maintenance. 1-micron or 3-micron repeat accuracy 24VDC solid-state output or 12VDC/24VAC contact output Ideal for detecting and measuring wear of cutting tools Direct input possible to microprocessors and programmable controllers Immersion-proof IP67

D5B’s detection of objects in multiple directions with high sensitivity makes it an ideal switch for usage in robotics. It operates even with a slight force and a slow-action mechanism is used. Its movement differential is as small as 0.01mm, assuring high accuracy of detection. High-sensitivity mechanical touch switch Detects objects in multiple directions and operates with slight force Movement differential of 0.01mm assures high accuracy of detection Gold-plated contacts capable of switching micro current/voltage load Highly resistant to dust, fine particles, water or oil splashes (IP67)

The D5C is a unique 18mm-dia. capacitive touch switch with a choice of three actuators. It can be activated with only a very slight physical contact. Lightweight objects, such as thin wire or foil, are accurately detected Amplifier, operation indicator and sensitivity adjuster on all models Conforms to IEC IP67 and NEMA Type 6, 6P Actuators can be freely interchanged between switch units Free-attachment type allows the attachment of any kind of actuator antenna

The D5F has a knife-edge mechanism in its optical system, which provides greater precision for a more stable output without faulty contact operation. 4-way high-precision optical switch Actuators have wear-resistant ceramic parts Optical system achieves 1µm operating position repeatability Reduced size and weight (34mm at operating section and 60g total) Immersion-proof IP67

A 'Disk On Module' is a solid state storage device, often taking the place of an IDE HDD. Industrial DOMs offer increased reliability as they have no moving parts to break, wear, or generate heat.

Compact DeviceNet I/O units with extensive diagnostic functions. Data regarding power supply status, I/O response times, operation counters and on-time are continuously recorded and checked against user-defined limits. Any deviation is reported to the control system, as indication to perform machine maintenance and prevent unplanned downtime. Smart DeviceNet I/Os are supported by PLC Function Blocks and HMI Smart Active Parts, allowing program-less visualisation and monitoring from the CJ1 PLCs and NS operator terminals.

Rugged I/O units for field mounting. The DRT2 slave units feature internal diagnostic and maintenance data collection, which can be accessed over the network. Power supply status, I/O response times, operation counters and on-time monitor data is available at all times, and is internally checked against user-defined limits. Maintenance warnings will be generated when limits are exceeded. Using CX-One or NS-series HMI with Smart Active Parts for visualisation, this allows more efficient system setup, commissioning and troubleshooting without any additional programming.

The DeviceNet safety input terminal DST-ID has 12 inputs for safety signals. Four test pulse outputs ensure crosstalk and short-circuit detection. Removable cage-clamp terminals for easy installation 12 inputs for safety signals 4 test pulse outputs to ensure crosstalk and short-circuit detection Status LEDs for advanced diagnostics Mixed-mode operation (safety and standard) for all inputs

The DeviceNet safety I/O-terminal DST-MD has 8 inputs for safety signals and eight solid-state safety outputs with up to 500mA. Four test pulse outputs ensure crosstalk and short-circuit detection of the inputs. Removable cage-clamp terminals for easy installation 8 inputs for safety signals 4 test pulse outputs to ensure crosstalk and short-circuit detection 8 solid-state outputs Status LEDs for advanced diagnostics

The DeviceNet safety I/O-terminal DST-MRD has four inputs for safety signals and four safety relay outputs with up to 2A. Four test pulse outputs ensure crosstalk and short-circuit detection of the inputs. Removable cage-clamp terminals for easy installation 4 inputs for safety signals 4 test pulse outputs to ensure crosstalk and short-circuit detection 4 relay outputs Status LEDs for advanced diagnostics

The DyaloX box industrial PC is created specifically for 24/7 operation and sets new standards in reliability, even in the most demanding industrial environments. A very flexible IPC, the box can be mounted in two different ways. Either separately so that a minimum amount of cabinet space is used, or it can be attached to the back of the touch screen in order to use it as a panel IPC. The DyaloX IPC makes use of Omron’s unique RAS self-diagnostic hardware and software, to ensure that it will keep on running and warn you if conditions become unstable.

The DyaloX panel industrial PC is created specifically for 24/7 operation and sets new standards in reliability, even in the most demanding industrial environments. The panel IPC is available with two different CPUs, namely an expandable 600 MHz model - ideal for running a wide range of basic applications, and a 1.3 GHz model for high-performance applications. Both models offer a choice of 12" and 15" touch panels. The DyaloX IPC makes use of Omron’s unique RAS self-diagnostic hardware and software, to ensure that it will keep on running and warn you if conditions become unstable.

DZ switches are ideal for switching circuits operating on two voltages and for controlling two independent circuits. DZ is interchangeable with Omron Z basic switches, as both switches are identical in mounting-hole dimensions, mounting pitch and pin-plunger position. Incorporates two completely independent built-in switches IP00

Extended sensing range inductive sensor in cylindrical brass housing The high quality and the long-life design of the E2A extended sensing distance provide the best value performance ratio for standard applications. Extended (double) sensing distance IP67 and IP69k for highest water protection DC 3-wire (NO, NC), DC 4-wire (NO+NC) Wide installation and connectivity range through modular concept For high grade stainless steel, see the E2EH. For the DC 2-wire, see the E2A DC 2-wire.

DC 2-wire inductive sensor in cylindrical brass housing The DC 2-wire models of the E2A family are easy to install and allow the detection of cable breakage. Extended (double) sensing distance IP67 and IP69k for highest protection in wet environments DC 2-wire

Long (triple) distance inductive sensor in cylindrical brass housing The E2A3 family features an optimised sensing performance to achieve triple sensing distance for flush mounting requirements. Triple distance for enhanced sensor protection from mechanical damage IP67 and IP69k For longer distance, see the E2Q5.

Inductive sensor for mobile usage in cylindrical brass housing Designed and tested to keep your mobile machines moving. IP69k tested and certified for highest water resistance e1 type approval (according to Automotive Directive 2005/83/EC) EMC noise tested after ISO 11452-2 and ISO 7637-2:2004 Cable breakage protection

Inductive sensor for explosive environments in cylindrical brass housing The high-reliability and robustness of the E2A family is also available for explosive environments. The protective structure of the E2A family (based on EN50014 and EN50281-1-1/2) allows the ATEX certification Group II category 3D (94/9/EC Appendix VIII) typically for explosive areas zone 22 with non-leading dust, for example flour. Protective connector cover to avoid disconnection under power Certified ATEX Group II category 3D (94/9/EC Appendix VIII) Rugged housing construction based on EN50014 and EN50281-1-1/2

High precision positioning inductive proximity sensor with separate amplifier The separate amplifier inductive sensor family E2C-EDA offers high precision distance positioning and detection. The teach-in function allows simple installation, and with the window function (2 outputs) production tolerance checks can easily be set up and modified. Typically several hundred µm detection precision Precision distance teaching Window function (2 outputs) for production tolerance checks For measurement and higher precision see ZX-E.

Oil resistant inductive sensor in cylindrical brass housing The standard E2E family offers tested oil resistance on commonly used oils in the automotive industry for reliable long-life operation in automotive assembly lines. Oil resistant PUR cable M8, M12, M18 and M30 standard sizes IP67g (water and oil resistance)

Miniature inductive proximity sensor in cylindrical metal housing The E2E Small Diameter line with housing sizes from dia 3 mm to dia 5.4 mm is part of the E2E family and is the ideal solution where space is crucial. The metal housing provides high mechanical protection. Miniature housing sizes from dia 3 mm to dia 5.4 mm Stainless steel or brass housing 3 kHz switching frequency For smaller housing sizes or longer sensing distances see E2EC.

Sub-miniature inductive sensor for demanding mounting conditions with remote amplifier The E2EC family features the smallest sensor heads for reliable sensing in areas where mounting space is crucial. The miniature sizes of the sensing heads are achieved by separating the sensing part from the amplifier. In contrast to standard separate amplifier models the E2EC family simplifies the installation as the amplifier is built into the cable. 3 mm diameter sensing head for smallest spaces 18 mm long ultra short M12 size housing Full metal housing model for highest resistance in demanding environments For miniature inductive sensors with built-in amplifier see E2E Small Diameter.

Heat and detergent resistant inductive sensor in cylindrical stainless steel housing The heat and detergent resistant inductive sensors provide reliable metal object or machine part detection in demanding environments such as food processing. Temperature resistant up to 120°C SUS316L housing with heat resistant plastic sensing face IP69k for highest water resistance ECOLAB tested and certified detergent resistance For detergent resistant stainless steel photo sensors, safety non-contact switches or fiber optic sensors see Processing Food.

Inductive proximity sensor in cylindrical full metal housing The high durability stainless steel sensing face provides more than 20 times longer protection against mechanical damage than conventional sensors. The high mineral oil and coolant resistance and the immunity against small metal chips on the surface make this sensor ideal for metal cutting or drilling applications. Full body stainless steel housing for highest mechanical protection Low frequency modulation for metal chip immunity Flame retardant cable for high protection against welding spatter damage For oil resistant photoelectric sensors in stainless steel housings see the E3ZM-C.

Chemical resistant inductive sensor in cylindrical PTFE housing The E2FQ features a full-body fluoro plastic housing for chemical resistance (e.g. against cleaning agents used in the semiconductor industry). Full body fluoro plastic housing for chemical resistance DC 2-wire and DC 3-wire models For fluoro plastic fiber optic sensors see the E32 Chemical resistant.

Long distance inductive proximity sensor in plastic housing The long sensing distance and simple installation on flat surfaces make the E2Q5 ideal for the detection of large metal objects for example in automotive assembly lines. M12 Plug-in connection Integrated short circuit and reverse polarity protection Active face position 90° turnable

Miniature square inductive sensor in plastic housing The E2S family features miniature block style plastic housings for simple mounting on flat surfaces. The durable plastic housing with front or side facing sensing surfaces, provide best value-performance ratio for machine part movement detection. Miniature housing with long sensing ranges Front and side facing sensing surfaces Simple mounting with one screw IP67 For the detection of non-metallic small objects see the EE-SX67.

E32 Standard Cylindrical E32 Square Shape E32 Miniature E32 Longer Distance E32 Chemical Resistant E32 Heat Resistant E32 Vacuum Resistant E32 Robot Application E32 Precision Detection E32 Area Monitoring E32 Special Application See http://industrial.omron.eu/en/products/catalogue/sensing/fiber_optic_sensors/default.html for more detailed product information.

High precision LASER sensor with separate amplifier The separate amplifier high-precision photoelectric sensors feature a large variety of different LASER sensing heads for highest precision positioning and object detection. Easy installation due to adjustable focus point and optical axis Wide range sensor head portfolio with different laser beam shapes Controller functions with easy wiring concept and power tuning function For higher detection precision and measurement see the ZX-LD.

Photoelectric sensor in plastic or brass M18 housing The cylindrical M18 size family offers a large standard portfolio in plastic or brass housings for through-beam, retro-reflective, diffuse-reflective and background-suppression models. For excellent price-performance for your standard applications. Plastic or brass housings IP67, IP69k for highest water resistance Special beam and LED models available

Photoelectric sensor in plastic or brass radial M18 housing Radial (angled) optics for easy mounting, installation and adjustment. Diffuse reflective and retro-reflective models IP67 and IP69k For through-beam or background suppression sensors for radial mounting or sensors for longer sensing distance in radial mounting see the E3FZ/E3FR.

Photoelectric sensor in stainless steel M18 housing The stainless steel housing provides enhanced detergent resistance and longer lifetime in demanding environments. Stainless steel housing ECOLAB certified detergent resistance IP67, IP69k for high water resistance

The slender M18-sized E3FS is a category-2 safety single beam with an operating range of up to 10m. Plastic and metal housing, cable and M12-connector offer flexibility in application together with a control unit such as F3SP-U3P or F3SP-U5P. Sensing distance up to 10m LEDs for easy alignment and diagnosis Cable and M12 plug categories Plastic and metal housing Category-2 sensor complying with EN 61496-1

Easy mounting photoelectric sensor in short M18 housing Secure-click snap mounting for fast installation High power LED for enhanced sensing distance Short housing with less than 40mm length Minimal optical axis deviation for easy alignment For metal housing see the E3F2. And for radial mounting with smaller head see the E3F2-[]41.

Long distance photoelectric sensor in plastic housing Long distance retro-reflective and teachable diffuse reflective sensors in plastic housing. Diffuse reflective model with 1.2m teachable setting distance M12 rotary connector or pre-wired models For long distance through-beam sensors see the E3Z Laser.

Long distance all voltage photoelectric sensor in plastic housing The E3G-M series offers the long sensing distance of the E3G family for all voltage (AC and DC) installations. 12 to 240VDC and 24 to 240 VAC power supply Terminal block connection For smaller size with AC/DC supply voltage see the E3JK.

All voltage photoelectric sensor in plastic housing The square sized E3JK family provides 12 to 240 VDC and 24 to 240 VAC power supply voltage. 12 to 240 VDC and 24 to 240 VAC supply voltage Relay outputs with long life expectancy and high switching capacity (3A, 250 VAC) For longer distance sensors with AC/DC supply voltage see the E3G-M.

Distance setting photoelectric sensor in metal housing Minimal black/white error for highest reliability detecting different colored objects (E3S-CL1) Setting distance up to 500 mm with reliable background suppression

Glass bottle detection photoelectric sensor in metal housing The special optical design of the E3S-CR62/67 ensures reliable detection of glass bottles compensating the often noticed 'double-detection-effect' when using other sensors. Special optical system for reliable bottle detection preventing 'lens effect' Thin beam for reliable bottle counting For general transparent material detection see the E3Z-B. And for enhanced detection stability on PET bottles see the E3ZM-B.

Photoelectric sensor for structured object detection in plastic housing The special wide beam optics of the E3S-LS3 ensures reliable detection of structured objects (with holes or different heights) and can be used for example to detect printed circuit boards (PCBs). Wide beam for reliable detection of structured, shiny and irregularly shaped objects For wide beam models in cylindrical M18 housing see the E3F2.

Photoelectric sensor in miniature plastic housing Small sized photoelectric sensors in flat and side view shape for demanding mounting conditions. Small size with precision pinpoint LED where space is crucial 3.5mm flat model with reliable background suppression and small black/white error Unique optical alignment technology ensuring minimal deviation of optical axis High EMC and ambient light immunity For smaller size see the E32 Square Shape.

Digital fiber amplifier with active threshold control for dust and dirt compensation The active threshold E3X-DA-AT-S digital fiber amplifier compensates for light power reduction caused by dirt and ensures stable operation. Active threshold control for high stability Alarm output for maintenance warning Area detection function for quality inspection or sensing range control

High functionality digital fiber amplifier with two large displays for excellent visibility even from a distance. Advanced timing, LED power and signal processing functions High resolution for long sensing distances and accurate settings Auto Power Control for long-term stability

E3X-DA-SE-S allows easy one button setting and provides the best value performance ratio for standard applications. Auto-teaching during machine operation Digital double display for incident level and threshold Object or 2-point teaching within a few seconds

The E3X-DAC-S detects the colour of a workpiece and enables it to be compared with a stored RGB ratio to identify coloured marks or workpieces. Moreover, it does this independent of the light intensity and minor sensing distance variations. White LED for colour independence Fast response time of min 60µs Timer function for variable ON or OFF delay up to 5s Remote teaching or easy one-button teaching

E3X-MDA incorporates 2 digital fiber amplifiers in one slimline housing. For applications requiring the detection of two objects simultanously the E3X-MDA provides an easy to use operation saving space and set-up time. Two digital amplifiers in one slimline housing Twin output models – on/off or area (between two threshold values) Signal comparison functions (AND, OR, etc.)

Fast response digital amplifier with potentiometer The E3X-NA_F provides a very fast response time and is the ideal amplifier for high speed detection applications. Short turn on time of only 20 μs Easy adjustment with potentiometer

The E3X-NA/E3X-SD is the ideal amplifier for basic fiber applications providing quick & easy adjustment. Easy adjustment with potentiometer (E3X-NA) or up/down keys (E3X-SD) Mutual interference prevention Enhanced water resistance types

General purpose sensor in compact plastic housing Compact housing size and high-power LED for excellent performance-size ratio and best value-performance ratio for standard applications. Minimal optical axis deviation for easy alignment IP67 and IP69K for highest water resistance Intensive shielding for highest noise immunity (EMC) Multiple molding housing for high mechanical resistance For detection of dirty lenses, misalignment and alarm functions see the E3Z condition monitoring: E3Z-_G, E3Z-_J.

The E3Z LASER sensor in compact plastic housing features visible LASER light for precision positioning and detection applications. Visible LASER light for precision positioning and small object detection High power LD for high functional reserve Class 1 LASER Precise background suppression and low black/white error for accurate detection For higher precision detection see the E3C Laser.

LASER sensor in compact plastic housing The E3Z LASER sensor in compact plastic housing features visible LASER light for precision positioning and detection applications. Visible LASER light for precision positioning and small object detection High power LD for high functional reserve Class 1 LASER Precise background suppression and low black/white error for accurate detection For higher precision detection see the E3C Laser.

Transparent bottle detection photoelectric sensor in compact plastic housing The E3Z-B provides easy adjustment for the detection of a large variety of standard transparent objects. Detects a wide range of bottles from single bottles to sets of stocked bottles IP67/IP69K tested for highest water resistance For enhanced detection stability for glass bottles see the E3S-CR62/67 and for PET bottles see the E3ZM-B.

Photoelectric sensor in plastic fork shape housing The forked shape optical through-beam sensors combine simple installation with reliable passage detection of object, machine parts or transportation elements like hanggliders. Fork shape for simple installation 1 or 2 axis models For smaller sized fork shaped sensors see the EE-SX47/67.

Photoelectric sensor for condition monitoring in compact plastic housing The E3Z 'condition monitoring' family features active or passive sensor function checking capabilities detecting misalignments, dirt covers, defective sensors, etc. E3Z-_-J0: Self-diagnostic alarm output on instable signal E3Z-_-G2: Detection of dirt cover by power reduction E3Z-_-G0: Active sensor functionality check by test input forcing state change at receiver (emission stop) For auto compensation of dust or dirt see the E3X-DA-AT-S.

Photoelectric sensor for condition monitoring in compact plastic housing The E3Z 'condition monitoring' family features active or passive sensor function checking capabilities detecting misalignments, dirt covers, defective sensors, etc. E3Z-_-J0: Self-diagnostic alarm output on instable signal E3Z-_-G2: Detection of dirt cover by power reduction E3Z-_-G0: Active sensor functionality check by test input forcing state change at receiver (emission stop) For auto compensation of dust or dirt see the E3X-DA-AT-S.

Photoelectric sensor with anti-tampering protection in compact plastic housing The E3Z-[]H line is part of the compact size E3Z family and features sensors without sensitivity adjusters for maximum tampering protection. Compact housing size and high-power LED for excellent performance-size ratio IP67 and IP69K for highest protection in wet environments Intensive shielding for highest noise immunity (EMC) Tough PBT housing for high mechanical resistance

Photoelectric sensor in compact stainless steel housing Compact housing size and high power LED for excellent performance-size ratio in a rugged, detergent-resistant stainless steel housing for demanding environments. High grade stainless steel housing (SUS316L) IP67 and IP69k for highest water resistance ECOLAB tested and certified detergent resistance For high grade stainless steel inductive sensors see the E2EH. And for high grade stainless steel Safety Non-contact switches see the F3S-TGR-N.

PET bottle detection sensor in compact stainless steel housing The p-opaquing optical system and the AC3 power control technology ensure highest stability for PET detection compensating dust on lenses and signal jitter caused by structured PET bottle surfaces. Stable PET detection using double refraction and AC3 power control technology Detergent resistant compact SUS316L housing Easy-to-use teach-in function For general transparent material detection see the E3Z-B. And for high performance glass detection see the E3S-CR67/67.

Oil-resistant photoelectric sensor in compact stainless steel housing The oil-resistant compact photoelectric sensors in a robust stainless steel housing feature an enhanced functional reserve for reliable object detection in dirty and mechanically demanding environments such as automotive assembly lines. Oil-resistant stainless steel housing IP67 and IP69K for maximum water resistance High visibility orange LED in through beam model For oil-resistant inductive sensors see the E2FM or the E2E.

Print mark detection photoelectric sensor in compact stainless steel housing The detergent resistant photoelectric sensor in a robust stainless steel housing provides reliable detection of all common print marks in food packaging applications. White LED for stable detection of differently colored print marks SUS 316L stainless steel housing Easy-to-use teach-in button or remote teach Fast response time of 50μs For smaller size and full RGB color detection performance see the E3X-DAC-S.

Easy-to-use, basic temperature controller with analogue dial setting Omron's basic ON/OFF or PD controller features an analogue setting dial. This compact, low-cost controller has a setting accuracy of 2% of full scale. It incorporates a plug-in socket allowing for DIN-rail or flush mounting. Compact, cost-effective controller Control mode: ON/OFF or PD Control output: relay Power supply: 100-120 / 200-240VAC Thermocouple K: 0 to 1200°C, L: 0 to 400°C, Pt100: -50 to 200°C

This multi-range 1/16 DIN controller with alarm function offers field-selectable PID control or ON/OFF control. The large, single display shows process value, direction of deviation from set point, output and alarm status. All setting field configurable with switches Multi-input (Thermocouple/Pt100) Clearly visible 3.5-digit display with character height of 13.5mm Control output: relay, voltage (for driving SSR) ON/OFF or 2-PID control with auto-tuning and self-tuning

This easy-to-mount multipoint temperature controller offers heat, cool and heat and cool control. It has voltage, analogue and NPN transistor control output and its parameters can be set via PC software or an E5ZD-SDL programming unit. Control mode: ON/OFF, hybrid or 2-PID control and fuzzy control Control output: voltage (pulse), analogue (current) and NPN transistor High-speed input sampling (200ms, all 8 channels) Connector terminal block saves wiring effort RS-232C, RS-422 and RS-485 communications available

In-panel, DIN-rail mounted modular multi-loop temperature controllers This modular temperature controller consists of 22.5mm-wide modules with 2 channels per module. Via RS-485 one can build up to a maximum of 32 control loops. The modularity of E5ZN enables easy exchange and replacement of the individual modules. Output: SSR, transistor, current, transfer outputs and event in- and outputs Alarms and load-fail detection, LED indicators for status Control mode: ON/OFF and 2-PID Easy connection to PLC and HMI or PC Configuration by separate setting unit (E5ZN-SDL) and tool software

The E5_K series of advanced controllers provides standard models and models with programmer functionality. The modular structure of the series makes it very versatile. A number of tuning functions are provided, including auto-tuning, self-tuning and fuzzy self-tuning. W48 x H96 x D100 / W53 x H53 x D100 / W96 x H96 x D100mm Control mode: ON/OFF or PID Control output: relay, SSR, voltage or current Universal inputs (Pt100/Thermocouple/Volt/Milliampere) Supported by ThermoTools PC Software

The E5_N general-purpose line of temperature controllers is available in 4 standard DIN formats. They all feature a high-intensity dual LCD display with a wide viewing angle. Except for the E5GN, the series features 3-colour PV change for easy status recognition. Control mode: ON/OFF or 2-PID Control output: relay, hybrid relay, voltage (pulse) or linear current Power supply: 100/240VAC or 24VDC/VAC Easy PC connection for parameter cloning, setting and tuning Easy set-up and operation

The new E5_N-H series take the proven E5_N features to the level of process control. The E5_N-H has the same easy way in which it is installed and operated, and has the same menu structure as the E5_N series. But the E5_N-H improves on accuracy, speed and process control features. Same Menu structure as E5_N Fast (60ms) and Accurate (0,1%PV) Universal inputs & modular outputs Setpoint profiles and parameter Banks Valve Control

The E5_R series provides you with high-accuracy inputs (0.01°C for Pt100) and a 50ms sample and control cycle for all four loops. Its unique Disturbance Overshoot Reduction Adjustment ensures solid, robust control. Easy and clear read-out thanks to bright liquid Crystal Display Exceptional versatility - multi-loop control, cascade control, and valve control Easy integration with DeviceNet, Profibus or Modbus SV programmer optional, 32 programs with up to 256 segments

Miniature size rotary encoder The E6A family of rotary encoders features a small sized dia 25mm housing. Small sized dia 25mm housing

Compact size rotary encoder The E6B family of incremental rotary encoders features a housing size dia 40mm. Line driver output models available

Multiturn rotary encoder The E6C-N rotary encoder provides a multiturn function for applications with rotations over 360°. Multiturn function

Improved water resistant rotary encoder The E6C family of dia 50mm incremental rotary encoders features an improved water resistance compared to standard models. IP64f or IP65f drip-proof, oil-proof construction

Improved water resistant rotary encoder The E6C family of dia 50mm incremental rotary encoders features an improved water resistance compared to standard models. IP65f drip-proof, oil-proof construction

Rugged housing rotary encoder The E6F family of dia 60mm rotary encoders features a rugged housing. Stronger shaft and higher durability (120 N in radial direction and 50 N in thrust direction) than previous E6F Encoders Drip-proof construction meets IP64F standards High-resolution models (1024 pulses max. per revolution) Faster response for high-speed control applications (grey code: 20 kHz)

Rugged housing rotary encoder The E6F family of dia 60mm rotary encoders features a rugged housing. Strong shaft for max 120 N in radial direction and max 50 N in thrust direction) Water- and oil-proof structure (IP65f)

Hollow shaft rotary encoder The E6H family of incremental encoders features a dia 40mm hollow shaft. Wide operating voltage range from 5 to 24 VDC Line drive output available (100 m max.)

The E7 is designed for variable torque applications such as fans and centrifugal pumps. It is supplied with V/f control and normal duty overload rating of 110% for one minute. A unique feature of the E7 is the energy-saving algorithm, which allows an extra saving of up to 20%. With an optional phase-shifting input transformer, the E7 dual-diode bridge can be operated in 12-pulse rectification mode, reducing input-current harmonic distortion. E7 IP54 solution with robust metal chassis and built-in RFI filter Adaptive energy-saving algorithm Silent operation 12-pulse configuration for low-current harmonics Programming software: CX-drive for parameter configuration

Photomicrosensor in plastic fork shape housing Standard photomicrosensors with 50 to 100 mA direct switching capacity for best value-performance ratio to detect machine parts or small objects. Response frequency up to 1 kHz Wide operating voltage range: 5 to 24 VDC For higher switching frequency or smaller size see the EE-SX91. For larger fork size sensors see the E3Z-G.

Photomicrosensor in thin fork shape plastic housing Thin shaped photomicrosensor for space saving mounting. Compact, thin profile enables dense mounting Indicator is visible from both sides Operating voltage range: 5 to 24 VDC

High-frequency photomicrosensor in fork shape plastic housing The small sized photo microsensors are ideally suited for the detection of machine ports where space is crucial. Up to 3 kHz (8 kHz average) switching frequency

Electromechanical relays are switching devices typically used to control high power devices. In such relays the switching mechanism that is part of an operating circuit, is activated by means of a relay solenoid coil through which the switching current flows. Electromagnetic relays generally comprise two primary components including a movable conductive cantilever beam and an electromagnetic coil.

The Electronic Line Shaft Application Software is the Omron-Yaskawa dedicated software for position and speed follower applications, allowing a slave drive to precisely follow a master encoder. It is the ideal solution for dual-motor synchronised applications. Position phase follower The speed and position ratio between the master and slave is infinitely adjustable A gear ratio can be adjusted from several sources The PG-Z2 option board is required for phase synchronisation Position offset advance/retard by digital/parameter or communication Varispeed F7 supported inverter

EtherCAT (Ethernet for Control Automation Technology) is an open high performance of Ethernet-based fieldbus system. The development goal of EtherCAT is to apply Ethernet to automation applications which require short data update times (also called cycle times) with low communication jitter (for synchronization purposes) and low hardware costs. See the EtherCAT group homepage for more info.

Intelligent Sensor with high speed image processing The F160 offers all features of the F150, including quick start-up, simple operation and an excellent price/value ratio. The main difference is that image capture and processing are accelerated many times. New functions include OCR, rotation search, customizable display and many more. Two camera connections - High-speed image acquisition Accelerated processing algorithms for all inspection tools Optical character recognition/verification tool Compact flash slot for storage of data and images Configurable user interface and monitor output

The F210 contains powerful algorithms such as Edge Code, Fine Matching and OCR/OCV. Inspection tasks can be configured easily via the user-friendly GUI. A Macro Function for OEMs and system integrators allows customization through which nearly every system function can be manipulated. Enhanced flexibility using branching and conditional operations Two camera connections Fine Matching tool-for-print quality inspection Edge Code (EC) technology for high-precision inspections High-speed Character Recognition/Verification tool

The F500/F210ETN are network ready, digital vision systems. The optional software VisionComposerNET allows configuration and maintenance of a vision network from a central PC. For documentation or later audits, the system provides tools for logging images and results for later analysis. Two digital camera ports, high resolution (1K x 1K) with F500ETN Advanced real time data logging and storage functions 10/100 Base TX Ethernet Port, USB, RS232/422, 33 digital I/O Optional VisionComposerNET for remote configuration/maintenance Security tools, audit trail creation in security sensitive environment

The F250 offers all inspection tools such as the F210, and in addition to that a hardware accelerated, ultra fast object location. 4 camera ports allow multiple inspection stations within one system. With an Ethernet interface, the F250 can communicate with almost every company computer system. Hardware accelerated inspection tools for extreme speed applications Four camera connections, Real-time object location tools Enhanced flexibility using branching and conditional operations 2 CF slots for data storage and logging Ethernet interface, 67 digital I/Os, RS232

Multi-beam sensor in flat aluminium housing The crossing of the multiple sensorheads provide a reliable area monitoring in a flat easy to install housing. Three models from 20cm length up to 1.8m are available. Flat 9 mm shape for easy design in elevator constructions Highest ambient light immunity (200,000 lux) for installations with direct sunlight exposition Robust aluminium housing Fulfills requirements of EN81-70 (1800mm models) for mounting in elevators For smaller size area monitoring see the E32 Area Sensing.

The F3S-B is a category-2 safety light curtain with resolutions of 30, 55 and 80mm. An operating range of up to 5m and protective heights from 300mm to 1,650mm are provided with a very small dead zone. Sensing distance up to 5m LEDs for easy alignment and diagnosis Series connection of two sensors is possible Category-2 sensor complying with EN 61496-1

The F3S-TGR-KxC perimetrical guards are available in category 2 and category 4 with integrated muting function. They are available as active/passive guards with two, three or four beams and an operating range of up 6m. Sensing distance up to 6m for active/passive type Muting function included (no additional controller needed) Two muting connection boxes for easy muting applications Automatic and manual restart function included Category-2 and -4 sensor complying with EN 61496-1

Non-contact switches monitor the status of guarding doors. LED for easy diagnosis and stainless steel housing for high hygiene demands in the food industry are available Operates with all Omron safety relay units and safety bus interfaces Operates behind stainless steel fittings Non-contact - no abrasion - no particles Conforms to safety categories up to 4 acc. EN 954-1 and PDF-M acc. EN60947-5-3.

The F3SH parametrical guards are available in category 4 with four beams and an operating range of up 10m. Detection height = Sensor length Sensing distance up to 10m LED bar for easy alignment and diagnosis Category-4 sensor complying with EN 61496-1

Category-4 safety light curtain/multi-beam safety sensor The F3SN family is a category-4 safety light curtain with resolutions of 14, 25, 30 and 60mm. An operating range of up to 10m and protective heights from 189mm to 1,822mm are provided with no dead zone. Detection height = Sensor length Sensing distance up to 7m (14mm resolution) and 10m for all other types LED bar for easy alignment and diagnosis Blanking function by using setup console Category-4 sensor complying with EN 61496-1

The F3SP-U3P muting controller can handle up to two safety single-beam sensors. It has a slim, 22.5mm-wide housing, two safety relay outputs with up to 2.5A and additional functions such as muting-lamp monitoring and override function. Two independent muting functions with override Slim housing: 22.5mm LEDs for status and diagnosis Detachable terminals Category-2 muting controller complying with EN 61496-1

The F3SP-U4P muting controller can handle up to two safety light curtains. It has a 45mm-wide housing, two safety relay outputs with up to 2.5A and additional functions such as muting-lamp monitoring and override function. Two independent muting functions with override Slim housing: 45mm LEDs for status and diagnosis Detachable terminals Fully certified according to EN 61496-1

The F3SP-U5P muting controller can handle up to four safety single-beam sensors. It has a 45mm-wide housing, two safety relay outputs with up to 2.5A and additional functions such as muting-lamp monitoring and override function. Two independent muting functions with override Slim housing: 45mm LEDs for status and diagnosis Detachable terminals Category-2 muting controller complying with EN 61496-1

The F3SS offers a long-distance operating range of up to 60m and complies with category 4. It is ideal for perimeter protection of multi-sided detection of intrusion into large machines. Sensing distance up to 60m LEDs for easy alignment and diagnosis Mutual interference protection included Robust metal housing with heating of lenses Category-4 sensor complying with EN 61496-1

The F7 drive is the industrial workhorse of adjustable frequency drives. It is intended to handle every conventional drive application found in a typical industrial manufacturing plant from simple variable torque pumping to sophisticated networked material handling. With excellent performance and a wide array of configurations and options, the F7 can be the single drive platform for an entire facility. Network communications, plug-in I/O cards, custom software and power/packaging options are among the many choices. For new installations or retrofits, the F7 is truly the industrial workhorse, perfect for every conventional application…and even some unconventional ones. Flux vector control. Excellent performance in open-loop mode with 150% torque at 0.5Hz Silent operation. No current de-rating in silent mode (high carrier frequency) Wide selection of option cards: fieldbus, PLC unit, Mechatrolink, analogue and digital I/Os, etc. Programming software: CX-drive for parameter configuration CASE (inverter application software) and PLC option board

A fiber optic sensor is a sensor that uses optical fiber either as the sensing element ("intrinsic sensors"), or as a means of relaying signals from a remote sensor to the electronics that process the signals ("extrinsic sensors").

It combines the I/O points with their field terminations into a modular package to save panel space and money. You can use distributed I/O nodes close to field devices for faster and more efficient wiring and troubleshooting. IP670 I/O terminals can be mounted in harsh environmental conditions. DRT2 Smart I/O units provide intelligent diagnostics and preventive maintenance functions in an oil and welding splatter resistant housing. For less severe conditions CompoNet slaves with IP54 protection offer an efficient alternative.

The protocol used by Omron to communicate between devices.

An electronic device that converts alternating current (AC) of one frequency to alternating current of another frequency. Omron portfolio solution of inverter drives boasts everything from the micro J7, through application dedicated drives such as the L7, up to the most advanced 3-level vector-control G7 frequency inverter.

Programmable text based function keys are available in two or four lines. Function key screens are suitable for applications in harsh environments such as gluing or painting stations. They are also recommended for simple use and where numerical data entry is frequent.

The G2RS relay sets new standards in feature design and reliability. These slimline interface relays give enhanced features and flexibility for more user-friendly installation, commissioning and operation. G2RS comes with standard nameplate and mechanical indicator. Space saving - 16mm with socket SPDT type 10A, DPDT type 5A LED indicator, colour coded green for DC versions, red for AC versions Test button, momentary and lockable, blue for DC, red for AC versions Screwless clamp-terminal sockets available

Non-bendable! First 6 mm relay with strong mechanical pins Drawing on years of experience, G2RV industrial slim relays have been added to the product portfolio. With a width of 6 mm, they offer significant space saving without compromising relay reliability or features. Push-in terminals and a full range of accessories are available for simplifying wiring and saving time. Large plug-in pins - excellent connection LED / mechanical flag - check operation Transparent housing - check condition Slim outline - space saving Push-in / accessories - simple wiring

This solid-state relay is compatible in shape and in size with the MK electromechanical relay and is mounted on a DIN-rail via sockets. There is also a DC-output model available with 3 to 125VDC load voltage range for high-voltage applications. 3 and 5A output current 5 to 110VDC/100 to 240VAC output voltages Compatible with MK electromechanical relays DIN-rail mounting via sockets Operation indicator to confirm input

This SSR is compatible in shape and size with the MY series of relays and is mounted on a DIN-rail using a socket. 2 and 3A output current 4 to 110VDC/100 to 240VAC output voltages Compatible with MY electromechanical relays DIN-rail mounting via sockets Operation indicator to confirm input

This SSR is compatible in shape and size with the LY series of relays and is mounted on a DIN-rail using a socket. 3A output current 4 to 48VDC / 100 to 240VAC output voltages Compatible with LY electromechanical relays DIN-rail mounting via sockets Operation indicator to confirm input

All models feature the same compact dimensions to provide a uniform mounting pitch. A built-in varistor effectively absorbs external surges. The operation indicator enables monitoring operation. 5-90A output current 24-480VAC/5-200VDC output voltages Built-in varistor Operation indicator (red LED) Protective cover for greater safety

This solid-state relay has a wide load voltage range: 75 to 264VAC. Both 100V and 200V loads can be handled with the same model. Dedicated, compact aluminum PCB and power elements are used. Its built-in varistor effectively absorbs external surges. 5-20A output current 75-264VAC output voltages Built-in varistor Quick-connect 110V input and 250V output terminals

Switching 75 to 150A at 240 to 440VAC The G3NH power solid-state relay switches 75 to 150A at 240 to 440VAC. It has a replaceable power cartridge and the easy-to-mount monoblock construction incorporates a heat sink. Incorporates operation indicator and varistor. A series of high-voltage (440V) models is available. 75 and 150A output current 100 to 440VAC output voltages Replaceable power cartridge Built-in operation indicator and varistor

Optimum design of the heat sink has contributed to the downsizing of this product. The power element cartridges of G3PA are easily replaceable for easy maintenance. G3PA can be mounted on a DIN-rail or using screws. 10-60A output current 24-480VAC output voltages Applicable with 3-phase loads Replaceable power element cartridges All features can be delivered with or without heat sink

The compact design of G3PB has been achieved by optimising the shape of the heat sink. The G3PB range provides you with a choice between DIN-rail mounting and screw mounting. Single and three phase, 15-45A output current 100-480VAC output voltages Applicable with 1-, 2- and 3-phase loads All features can be delivered with or without heat sink Conforms to CE marking, EN (VDE approval), CSA and VDE standards

This slim, 22.5mm-wide, solid-state relay with built-in transformer detects load failures. The automatic shut-down function on overload condition protects heater loads. Its built-in heat sink increases life and reliability. SSR that detects SSR short and open circuits Alarm output Slim design - 22.5mm with heat sink DIN-rail and screw mounting

Omron’s unique design and carefully selected materials made it possible to produce a compact and lightweight power controller. AC power controller with phase-control system Single-phase models Base-up and soft-start functions available Detection of heater disconnection and single heater burnout Over-current detection

High-speed models with optimum input ratings for a variety of sensors are available, as well as input and output modules that can be used for the G2R. Use a coupler conforming to VDE 0884 and assuring an I/O dielectric strength of 4,000V. 1.5 and 2A output current 5 to 200VDC/100 to 240VAC output voltages Compatible with G2RS electromechanical relays DIN-rail mounting via sockets Operation indicator to confirm input

The G3ZA receives manipulated variables generated by control loops or manual settings via a simple-to-wire RS-485. It regulates the heater power with high precision by driving up to eight standard SSRs. Moreover, the offset control reduces peak power in the supply net. Multi-channel power controller Controls up to eight standard solid state relays Easy integration with PLC Compact size Available with heater alarms (four channels) or without (eight channels)

Each contact in the double-pole contact mechanism performs alternate make-brake operation at each pulse input and is thus ideal for alternate operation or transfer/switching operation of a motor. Positive operation is assured due to the unique ratchet mechanism Satisfies dielectric strength of 2,000VAC Low power consumption (AC: approx. 6.4VA; DC: approx. 3.9W) DPDT contact configuration

The G7 has the world's first 400V 3-level inverter architecture that eliminates or minimises the installation problems associated with IGBT switching (very long cable lengths, bearing currents and common-mode currents) and protects the entire motor-drive system. The G7 can be programmed using DriveWorksEZ™. This is a PC-based, object-orientated, user-friendly, graphical icon programming tool. 3-level control reduces voltage peaks on motor windings by up to 50%. There is no need for an AC reactor on long motor cables. Flux-vector control. Excellent performance in open-loop mode with 150% torque at 0.3Hz. Silent operation. No current de-rating in silent mode (high carrier frequency) Wide selection of option cards: fieldbus, PLC unit, Mechatrolink, analogue and digital I/Os, etc. Programming software: CX-drive for parameter configuration. DriveWorkEZ for object-orientated programming.

The G7 has the world's first 400V 3-level inverter architecture that eliminates or minimises the installation problems associated with IGBT switching (very long cable lengths, bearing currents and common-mode currents) and protects the entire motor-drive system. The G7 can be programmed using DriveWorksEZ™. This is a PC-based, object-orientated, user-friendly, graphical icon programming tool. 3-level control reduces voltage peaks on motor windings by up to 50%. There is no need for an AC reactor on long motor cables. Flux-vector control. Excellent performance in open-loop mode with 150% torque at 0.3Hz. Silent operation. No current de-rating in silent mode (high carrier frequency) Wide selection of option cards: fieldbus, PLC unit, Mechatrolink, analogue and digital I/Os, etc. Programming software: CX-drive for parameter configuration. DriveWorkEZ for object-orientated programming.

With a rated load current of 25A due to the miniature hinge for maximum switching power, the G7J can switch both motor loads as well as resistive and inductive loads. G7J has no contact chattering for momentary voltage drops up to 50% of its rated voltage. 4PST-NO, 3PST-NO / SPST-NC or DPST-NO / DPST-NC contact types Quick-connect, PCB or screw terminals 25A rated load Compatible with momentary voltage drops Can be used like a contactor

A high-capacity, high-dielectric-strength relay compatible with momentary voltage drops. G7L is equipped with a double-break mechanism and a test button (excluding -P models). SPST-NO or DPST-NO contact types Quick connect, PCB or screw terminals 20, 25 or 30A rated load Compatible with momentary voltage drops Wide range of applications with 100 or 200V coils

The G7S six-pole relay family is available in various contact combinations and offers reinforced insulation and forcibly guided contacts. Terminals are arranged for easy PCB layout. It can be soldered directly to a PCB or used together with the P7S socket. Forcibly guided contacts Conforms to EN 50205 3A at 240VAC and 3A at 24VDC for resistive loads Low-power coil

The slim G7SA relay family with forcibly guided contacts is available as a four- or six-pole type in various contact combinations and offers reinforced insulation. Terminals are arranged for easy PCB layout. It can be soldered directly to a PCB or used together with the P7SA sockets. Forcibly guided contacts Conforms to EN 50205 6A at 240VAC and 6A at 24VDC for resistive loads Reinforced insulation between inputs and outputs and poles 4- and 6-pole relays available

Compact 160 Amp Power Relay G7Z series provides a compact, cost efficient solution for applications such as inverters, UPS, solar and fuel-cell battery circuits. Relay in combination with auxiliary contact block meets EN 60947-4-1. Coil ratings are available in 12 and 24 VDC. Power consumption is less than 4 watts. Switching current 160 A (40 A rating / 4-pole / IEC-AC1) Switching voltage 440 VAC Safety function with mirror contacts in various configurations Power consumption less than 4 Watts Low Switching Noise (70 dB)

G9SA-family offers a complete line-up of compact and expandable safety relay units. Modules with safe OFF-delay timing are available as well as a two-hand controller. Simple multiplication of safety contacts is possible by using the connection on the front. 45mm-wide housing, expansion units are 17.5mm wide Safe OFF-delay timer Simple expansion connection Certification up to category 4 according to EN954-1 depending on the application

G9SA-TH covers two-hand control applications up to type IIIc according to EN574 in a 45mm-wide housing. Units with power supply voltage of 24VAC/VDC and 100 to 240VAC are available for flexibility in application. 45mm-wide housing, expansion units are 17.5mm wide Two-hand control according to EN 574 type IIIc Simple expansion connection Certification up to category 4 according to EN954-1 depending on the application

G9SB is a family of slender safety relay units, providing two safety contacts in a 17.5mm- and three safety contacts in a 22.5mm-wide housing. 17.5mm- and 22.5mm-wide housing 1- and 2-input channel units Manual and automatic reset units Certification up to category 4 according to EN954-1 depending on the application

G9SX-family modules can be connected by a logical “AND” function to implement partial/global stopping of a machine. Solid-state outputs, detailed LED diagnosis and clever feedback signals help to keep maintenance easy. The line-up is completed by expansion units with safe timing functions. Clear and transparent segmentation of safety functions by use of unique "AND" connection Solid-state outputs for long life and relay outputs in extension box available Detailed LED indications enable easy diagnosis Clever feedback signals for easy maintenance Category-4 according to EN954-1 and SIL 3 according to EN 61508

This motor timer series provides you with many features, such as ON-delay, time indicator, moving pointer and synchronous motor. Moreover, the LED indicator shows the time operation, time range and the rated voltage. DIN-sized 48 x 48mm Front-panel/plug-in/DIN-rail All supply voltages available 0.2 s to 30 h SPDT, 6A at 250VAC

The H3AM has an easy-to-read large setting dial with moving pointers, a wide time-setting range of 0.2 s to 60 h and a broad AC power supply range (100 to 240VAC). The programmable contact facilitates the building of a self-holding relay circuit as well as built-in instantaneous contact. Front 96 x 96 x D 85mm Front panel 100 to 240VAC 0.05 s to 60 h DPST, 5A at 250VAC

This elaborate range of solid state timers provides you with a multi-functional timer, twin timer, star-delta timer and a power OFF-delay timer. 48 x 48mm front-panel/plug-in High-/low-voltage models (except -H and -G) 0.05 s to 300 h (except -H and -G) DPDT, 5A at 250VAC Transistor 100mA at 30VDC

The H3DE series of timers provides a wide AC/DC power supply and time range to reduce the number of items. H 79 x W 22.5 x D 100mm DIN-rail mounting 24-230VAC/VDC (except -H) Wide time setting range: 0.10 s - 120 h (except -H and -G), 8 ranges

This broad range of timers includes many functionalities and has a wide AC/DC power supply range. Models with screwless clamp connection available. 17.5mm width, modular 45mm DIN-rail mounting 24-48VDC and 24-230VAC 0.1 s to 120 h, 7 ranges

The H3FA timer has four selectable time ranges, depending on the model. The timer operation can also be controlled through an external variable resistor. It can be mounted on a 24-pin IC socket. PCB-mounting timer H 20 x W 17.75 x D 36.9mm 5, 6, 12 or 24VDC 0.1 to 60 min SPST-NO and SPST-NC 3A

This ultra-slim solid state timer is ideal for usage where space is limited. Multiple time ranges and operating modes can be chosen using DIP-switches. Power-ON and relay-ON indicators provide easy monitoring. H 46 x W 13 x D 29mm Plug-in 12VDC, 24VDC and 24VAC 0.1 s to 10 min and 0.1 min to 10 h SPDT or DPST-NO

H3YN features 4 multi-operating modes: ON-delay, interval, flicker ON start and flicker OFF start. H 28 x W 21.5 x D 52.6mm Plug-in All supply voltages available 0.1 s to 10 h DPDT (5A) or 4PDT (3A)

H5CX offers you the most complete series of products on the market today. Based on extensive customer research, these new timers have been designed with added-value features that users both need and appreciate. H 48 x W 48 x D 64 to 100mm Two-colour display value, red or green Front-mounting / plug-in 0.001 s to 9999 h, 10 ranges Input NPN, PNP and contact

H7BX with the backlit LCD gives a excellent display view. The main display PV has a height of 13.5mm and SV has a height of 9.5mm. It can be green or red and it can be programmed to change if a specific value is reached. All basic counters functions are covered with many different output modes. Easy setup by dip-switches for the basic functions. H 72 x W 72 x D 100mm Total and preset counter, batch counter, dual counter and tachometer Two-color display value, red or green 6-digit, -99999 to 999999, set value -99999 to 999999 or 0 to 999999 Input contact, NPN or PNP Easy operation with a key for each digit

H7CX offers you the most complete series of products on the market today. Based on extensive customer research, these new counters have been designed with added-value features that users both need and appreciate. H 48 x W 48 x D 64 to 100mm Two-colour display value, red or green Front-mounting/plug-in 6-digit model -99999 to 999999, set value -99999 to 999999 or 0 to 999999 Input contact, NPN or PNP

Self-powered LCD totaliser The H7E series is available with large display with 8.6mm character height. It includes models with backlight for improved visibility in dimly lit places. The H7E family includes total counters, time counters, tachometers and PCB-mounted counters. H 24 x W 48 x D 55.5mm 8 digits, 8.6mm character height Black or light-grey housing Dual input speed: 30Hz <-> 1kHz Short body: all models have a depth of 48.5mm

Self-powered tachometer The H7E series is available with large display with 8.6mm character height. It includes models with backlight for improved visibility in dimly lit places. The H7E family includes total counters, time counters, tachometers and PCB-mounted counters. H 24 x W 48 x D 53.5mm 5 digits, 8.6mm character height Black or light-grey housing Dual revolution display

The H7E series is available with large display with 8.6mm character height. It includes models with backlight for improved visibility in dimly lit places. The H7E family includes total counters, time counters, tachometers and PCB-mounted counters. H 24 x W 48 x D 55.5mm 7 digits, 8.6mm character height Black or light-grey housing Dual time range 999999.9h <-> 3999d23.9h or 999h59m59s <-> 9999h59.9m

The H7E_-N_P is a PCB-mounted counter. It is available as a total counter (8-digit) or as a time counter (999999.9h). Dedicated for usage on a PCB Total counter (8-digit) Time counter (999999.9h)

The H7GP features a high-visibility, negative transmissive LCD display with 8.5mm-high characters and built-in red LED backlight with low power consumption. It has a compact (80mm) body. Total/timer counter H 24 x W 48 x D 80mm Red negative transmissive LCD 6 digits, 8.5mm height 12-24VDC or 100-240VAC

The H7HP has a large, easy-to-read display: 15mm-high characters for 6-digit models or 12mm-high characters for 8-digit models. It features a high-visibility, negative transmissive LCD display with built-in red LED backlight with low power consumption. It has a compact (66mm) body. Total/timer counter H 36 x W 72 x D 65.8mm Red negative transmissive LCD 6 digits, 15mm height / 8 digits, 12mm height 12-24VDC or 100-240VAC

The H8GN is a 1/32 DIN timer and counter in one. It is simple to switch between the timer and counter functions. During operation it is also possible to switch the display to monitor the totalising count value in 8 digits. Many sophisticated functions come standard with H8GN. H 24 x W 48 x D 83mm 8-digit display, 4 value and 4 set value Front mounting 0.001 s to 9999 h (configurable) 24VDC

World's smallest compact preset counter/timer The H8GN is a 1/32 DIN timer and counter in one. It is simple to switch between the timer and counter functions. During operation it is also possible to switch the display to monitor the totalising count value in 8 digits. Many sophisticated functions come as standard with H8GN. H 24 x W 48 x D 83mm 8-digit display, 4 value and 4 set value Front mounting -999 to 9999 24VDC

The H8PS provides high-speed operation at 1,600 r/min and high-precision settings to 0.5° ensuring widespread application. H8PS features a highly visible display with back-lit negative transmissive LCD. Advance angle compensation function compensates for output delays. 96 to 121.2Hx96Wx60.6 to 67.5D mm Front-panel / DIN-rail 24VDC 8-, 16- and 32-outputs NPN/PNP 100mA at 30VDC

With a highly rigid, dust- and drip-proof construction, HL-5000 can be used in a variety of heavy industrial applications. Highly rigid construction (head and cover snugly fit in box) Smooth operation with greater overtravel Easy-to-wire conduit-opening design Models with grounding terminals conform to the CE marking Jet-proof IP65

Operator Control and Monitoring Systems with PLC and Human Machine Interface. The Omron SYSMAC One Series is a combination of a NS Series HMI, a choice of two powerful CJ1 Series PLCs, an optional Ethernet interface and a standard second network interface (DeviceNet or Profibus).

Code reading and Radio Frequency Identification (RFID)are the technologies to identify and trace products in any process on the factory floor.

An inductive sensor is an electronic proximity sensor, which detects metallic objects without touching them. The industry standard inductive sensors provide the highest reliability for machine part and mteal object detection from short to long distance detection, in special environments, for special mounting conditions, special applications or special connectivity requirements.

With simplicity and cost-effectiveness in mind, the J7 was designed to meet low-end simple applications such as conveyors, fans and pumps in small power applications. With on-line torque compensation the J7 can deliver 100% torque down to 1.5Hz. For quick installation and set-up the J7 is fitted as standard with a digital operator and speed volume. Easy to use. Just WIRE and RUN. Good torque performance: 100% torque at 1.5Hz, 150% at 3 Hz Compact size RS485 and RS232 option unit Programming software: CX-drive for parameter configuration

This modular system consists of main contactors and additional contact blocks. The basic units can be combined with auxiliary contacts (top mounting). Reversed versions, including integrated mechanical interlock, are available as well as 3-main-pole and 4-main-pole versions. 4kW and 5.5kW versions are available Different coil voltages (AC and DC) Mini and normal-size versions are available The contactors can be mounted with screw fixing and snap fitting on a DIN-rail All components are finger proof

Three basic units can be combined with different additional auxiliary contacts. 4-pole, 6-pole and 8-pole versions in different configurations are possible as well as different coil voltages (AC and DC). Accessories such as suppressors are available. Mirror contacts Screw fixing and snap fitting (35mm DIN-rail) Rated current = 10A (I-th) Suitable for electronic devices (DIN 19240) Finger proof (BGV A2)

The J7MN motor starters protect motors against thermal overload and short circuit. The Motor protection circuit breakers can be equipped with additional auxiliary contacts, front or side mounted. Other options are circuit trip alarm units, undervoltage and shunt release units. To make wiring easy we provide as well busbar system. Available rated operational currents to 32 A, 63 A and 100 A Switching capacity is mainly 50 kA/400 V or 100 KA/400 V All Motor Protection Circuit breaker can be mounted on a DIN-rail For the range to 32A we provide electro-mechanical links modules All components are finger proof

J7TKN relays protect motors against thermal overload. They can be mounted on the contactor or separately. The relays comply with IEC 947 (single-phase sensitivity). Series of overload relays covering a setting range from 0.24A to 220A All components are finger proof

Junma compact servo drive with built-in MECHATROLINK-II significantly reduces wiring and set-up time, while saving up to 30% of cabinet space. The Junma series is the first in the world to be fully tuning-free and program-less.

Junma series of ultra-compact, pulse-train-controlled servo drives, significantly reduces set-up time, while saving up to 44% of cabinet space. The series is the first in the world to be fully tuning-free and program-less.

The NS300 is the drive-based solution for simple and reliable positioning using DeviceNet. No programming language is necessary Up to 63 drives can be connected in a network Supports polling I/O and explicit messages Parameters are maintained by the PLC Various positioning modes (homing, multistep and speed positioning

The NS500 is a flexible and simple distributed control over Profibus DP. It connects directly to the Sigma II and has several positioning modes, making it simple to configure.

The NS600 provides flexible and simple distributed control. lt connects directly to the Sigma II and has several positioning modes, making it simple to configure. It supports a standard RS485/422 and discrete I/O control.

Accurately detects a burned heater element or elements incorporated by a moulding machine or packing machine and outputs an alarm signal. Precisely singles out the burned element even if one heater element among several heater elements has been burned out. Applicable to small- to large-capacity heater elements Voltage-fluctuation-compensation function eliminates false alarms All K2CU-F large-capacity models work with both 1- and 3-phase heaters

The K3GN is able to cover a wide variety of applications with its 3 main functions: process meter, RPM processor/tachometer and digital data display for PC/PLC. Configuration is easy and the design is advanced and compact. Process indicator DC voltage/current RPM process/tachometer Digital data display for PC/PLC Very compact 1/32 DIN housing: H 24 x W 48 x D 83mm 5-digit display with programmable display colour, in red or green

These indicators with digital input feature a clear and easy-to-use colour-change display. All models are equipped with an IP66 housing. K3HB-C is high speed, with a sample rate up to 50kHz. Position meter indication for easy monitoring Optional DeviceNet, RS-232C, RS-485 Double display, with 5 digits, in two colours Dimensions: H 48 x W 96 x D 100mm

These indicators with analogue input feature a clear and easy-to-use colour-change display. All models are equipped with an IP66 housing. K3HB series is high speed, with a sample rate of 50Hz. Position meter indication for easy monitoring Optional DeviceNet, RS-232C, RS-485 Double display, with 5 digits, in two colours Dimensions: H 48 x W 96 x D 100mm

Timer interval indicator measuring time, passing speed or 2-point cycles These indicators with digital input feature a clear and easy-to-use colour-change display. All models are equipped with an IP66 housing. Position meter indication for easy monitoring Optional DeviceNet, RS-232C, RS-485 Double display, with 5 digits, in two colours Dimensions: H 48 x W 96 x D 100mm

Rotary pulse indicator capable of 50kHz measurements These indicators with digital input feature a clear and easy-to-use colour-change display. All models are equipped with an IP66 housing. K3HB-R is high speed, with a sample rate up to 50kHz. Position meter indication for easy monitoring Optional DeviceNet, RS-232C, RS-485 Double display, with 5 digits, in two colours Dimensions: H 48 x W 96 x D 100mm

Linear sensor indicator capable of high-speed response These indicators with analogue input feature a clear and easy-to-use colour-change display. All models are equipped with an IP66 housing. K3HB series is high speed, with a sample rate of 2,000Hz. Position meter indication for easy monitoring Optional DeviceNet, RS-232C, RS-485 Double display, with 5 digits, in two colours Dimensions: H 48 x W 96 x D 100mm

Weighing indicator measuring pressure, load, torque and weight These indicators with analogue input feature a clear and easy-to-use colour-change display. All models are equipped with an IP66 housing. K3HB series is high speed, with a sample rate of 50Hz. Position meter indication for easy monitoring Optional DeviceNet, RS-232C, RS-485 Double display, with 5 digits, in two colours Dimensions: H 48 x W 96 x D 100mm

Process indicator ideal for discriminating and displaying measurements These indicators with analogue input feature a clear and easy-to-use colour-change display. All models are equipped with an IP66 housing. K3HB series is high speed, with a sample rate of 50Hz. Position meter indication for easy monitoring Optional DeviceNet, RS-232C, RS-485 Double display, with 5 digits, in two colours Dimensions: H 48 x W 96 x D 100mm

Highly visible LCD display with 2-colour (red and green) LEDs The K3MA-F is a frequency/rate meter with a supply voltage of either 100 to 240VAC or 24VAC/VDC. Both are equipped with the same quality display and have the same short depth of 80mm. DIN-size of H 48 x W 96mm Highly visible, negative transmissive back-lit LCD display 14.2mm-high characters 5 digits (-19999 to 99999) Front-panel IP66

Highly visible LCD display with 2-colour (red and green) LEDs The K3MA-J is a process meter with a supply voltage of either 100 to 240VAC or 24VAC/VDC. Both are equipped with the same quality display and have the same short depth of 80mm. DIN-size of H 48 x W 96mm Highly visible, negative transmissive back-lit LCD display 14.2mm-high characters 5 digits (-19999 to 99999) Front-panel IP66

Highly visible LCD display with 2-colour (red and green) LEDs The K3MA-L is a temperature meter with a supply voltage of either 100 to 240VAC or 24VAC/VDC. Both are equipped with the same quality display and have the same short depth of 80mm. DIN-size of H 48 x W 96mm Highly visible, negative transmissive back-lit LCD display 14.2mm-high characters 4 digits Front-panel IP66

This very compact plug-in leakage controller fits into Omron's G2R 8-pin sockets (P2RF-08-E). K7L detects a wide variety of liquids, ranging from water to liquid chemicals with low conductivity. Operation range: up to 50MΩ Four sensing ranges available Detection method: conductive Two LEDs: green for power supplied, red for output indication Conforms to EMC and LVD Directives, UL/CSA approved

These single-phase current relays monitor over- and undercurrents. Manual resetting and automatic resetting are supported by one relay. The start-up lock and operating time can be set separately. The relay warning status is easily monitored with the LED indicator. Single-phase current relay In 22.5mm-wide industrial housing Under or over control Supply voltages: 24VAC/24VDC/115VAC/230VAC Easy wiring with ferrules

Monitors voltage asymmetry, phase sequence and phase loss for 3-phase 3-wire or 4-wire power supplies, in one unit. Worldwide power specifications supported by one unit Phase sequence, phase loss: operation reaction time 0.1s maximum Asymmetry: operation time setting from 0.1 to 30s Reset method: automatic Power ON lock: 1s or 5s

K8AB-PH simultaneously monitors phase sequence and phase loss for 3-phase 3-wire power supplies. The relay warning status can easily be monitored using the LED indicator. Suitable for industrial facilities and equipment. 3-phase sequence, phase-loss relay Monitors both functions at once Measuring range: 200 to 500VAC Power supply voltage is the same as measuring voltage Operation reaction time: 0.1s maximum

Monitors overvoltages and undervoltages for 3-phase 3-wire or 4-wire power supplies, in one unit. Switch setting for 3-phase 3-wire or 3-phase 4-wire power supply. Overvoltages or undervoltages: operation time setting from 0.1 to 30s Relay warning status can easily be monitored using the LED indicator Separate outputs possible for overvoltages and undervoltages Reset method: automatic Power ON lock: 1s or 5s

This temperature monitoring relay was designed specially for monitoring abnormal temperatures to prevent excessive temperature increase and to protect equipment. K8AB-TH provides temperature monitoring in slim design with a width of just 22.5mm. Simple function settings using DIP switch Selectable alarm latch and SV setting protection Multi-input support for thermocouple or Pt100 sensor input Changeover relay: fail-safe selectable Alarm status identification with LED

This temperature monitoring relay was designed specially for monitoring abnormal temperatures to prevent excessive temperature increase and to protect equipment. K8AB-TH provides temperature monitoring in slim design with a width of just 22.5mm. Simple function settings using DIP switch Selectable alarm latch and SV setting protection Multi-input support for thermocouple or Pt100 sensor input Changeover relay: fail-safe selectable Alarm status identification with LED

These single-phase voltage relays are for monitoring over- and undervoltages. Manual resetting and automatic resetting are supported by one relay. Relay warning status can easily be monitored using the LED indicator. Single-phase voltage relay In 22.5mm-wide industrial housing Under or over control Supply voltages: 24VAC/24VDC/115VAC/230VAC Easy wiring with ferrules

For monitoring over- and undervoltages simultaneously. Manual resetting and automatic resetting are supported by one relay. Separate settings and outputs are supported for over- and undervoltages. Relay warning status can easily be monitored with the LED indicator. Single-phase voltage window relay In 22.5mm-wide industrial housing Under and over, low/low or high/high control Supply voltages: 24VAC/24VDC/115VAC/230VAC Easy wiring with ferrules

The L7 is the ultimate drive for lift applications up to 3m/s. High starting torque, silent operation, lift-specific operator interface and operation with both AC and PM motors are standard features of the L7 inverter. One model to control AC and PM motors Silent operation with no current de-rating Safety Cat 3 stop. Cat 0 embedded as standard. Battery operation for emergency rescue. Motor auto-tuning at standstill and at RUN Programming software: CX-drive for parameter configuration

The LET-LA linear sliders are based on the SGLFW iron-cored linear motors. With the aid of the outstanding "automatic motor recognition" technology, start up of the sliders takes less than 15 minutes. The sliders are available in two versions, one without a cover and one with a complete cover. Reduction of total machine development time THK bearings with caged ball technology included Numerik Jena linear encoder included Positioning repeatability down to 1 µm Moving speed up to 5 m/sec

To save your in-house development resources, Omron can deliver customised linear motion systems including motion controllers and pre-programmed applications. The whole linear product range of iron-core and iron-less motors as well as linear sliders can be used to develop solutions which perfectly match customer requirements. Total solutions consist of mechanical components, linear motors and motion controllers Reduction in total machine development time All Omron Yaskawa linear motor products can be used Plug & Play x/y tables and gantry systems Development and production inside Europe

The function of a limit switch is to produce electrical signals corresponding to the position of the mechanical member to be detected. Limit switches have operating heads which incorporate some type of lever arm or plunger mechanism; the selection of which is application dependent.

Linear Servo Motors feature plug-and-play connection with the Sigma II and XtraDrive servo drives through use of automatic motor recognition and serial encoder technology. We offer motors with a peak force of up to 7500N and a maximum speed of 5m/s.

A miniature power relay The LY series is equipped with arc barrier and built-in diode. LY comes in single-, double-, three- and four-pole models. The available mounting types are DIN-rail by socket, PCB & flange mounting. SPDT, DPDT, 3PDT and 4PDT contact types DIN-rail by socket, PCB and flange mounting types available 10A rated load

The M16 series of nut-mounted indicators comes in rectangular, square and round versions. Due to its modular construction, assembly is quick and easy. M16 comes in a wide variety of control and signal devices with a wide range of switching capacities, from general load to micro load. LED, incandescent and neon lamp Snap-in switch unit Short mounting depth, less than 28.5mm below panel High reliability, IP65 UL and CSA approved, conforms to EN60947-5-1

The M22 series of indicators comes in 22 or 25mm-diameter round versions. They can easily be mounted and removal of the socket unit is also easy. The finger-protection mechanism on the lamp is provided as a standard feature. M22 indicators can be equipped with an LED or incandescent lamp. Available in 5 colours Super-bright LEDs for all versions Lamp sockets with or without transformers UL and cUL approved

High-precision motion controller with multi-tasking G-Language programming. The MC module provides closed-loop control via analogue outputs for up to 4 axes and supports G-Language for advanced, high-speed, high-precision position control. Several modules can be supported per PLC CPU.

CS1 solution for advanced motion control. The MC402 is a PLC-based advanced motion controller. It controls 4 axes and up to 16 modules can be installed in the same PLC. The module controls the position speed or torque of the servo drive via an analogue output. This PLC-based condition opens the controller to the whole system.

30-axes advanced motion controller over MechatroLink-II Motion Bus. The MCH is a compact module that enables the development of advanced applications. It supports 30 real axes and 2 virtual axes. Its advanced motion includes e-cam, ELS and registration.

The MCW151 is a powerful servo-based controller. Complex motions such as cams, gears, linked axes and interpolation are made easy with a comprehensive BASIC command set.

For the highest measurement performance on all kinds of surfaces and objects. The Smart Sensors are the answer for high speed, high resolution applications in any distance. The easy system integration assures a 'zero-defect process'.

The Microsoft Foundation Classes are a library of C++ classes for programming Windows applications.

These modular configurations consist of main contactors plus additional contact blocks. Several contact configurations are possible. They can be mounted with screw fixing and snap fitting to a DIN-RAIL.

The mini version of our series of motor contactors covers the range from 4kW up to 5.5kW. The modular system consists of main contactors plus auxiliary contact blocks and several contact configurations are possible.

The MK(S) series has proven to be exceptionally reliable since its introduction almost 50 years ago. In order to provide the same easy testing as our other relay families, the MK-S is equipped with a lockable test button offering the same function/operation as the MY(S) and G2R(S) families. 8-pin DPDT and 11-pin 3PDT contact types Switching current up to 10 A Lockable test button for easy testing Temperature rating from -40C up to 60C

The Modbus Organization is a membership-based trade association of independent users and suppliers of automation devices. See Modbus Organisation website for more info.

Modular I/O (input/ output) devices allow a large number of voltage, mA, temperature and digital signals to be monitored or controlled by a remote computer or PLC. Measurements are communicated using Modbus or ASCII protocols over Ethernet or RS485 to the remote computer.

A PLC configuration in which each component is split into a separate unit. A modular PLC lets you have as many inputs and outputs as you want.

Be it for standalone, PLC-based or servo-based motion controllers, Omron is the right choice. Offering programming simplicity without compromising on system performance from 1 to 256 axes. Functions like axis inrerpolation, master-slave, e-cam and multi-axis synchronisation over conventional I/Os or a robust digital servo-link are readily available.

The MP2100 is a high-performance motion controller based on Mechatrolink II motion bus. It can perform advanced motions such as e-cam, line synchronisation and multiple interpolation functions.

The MP2200 is a true system controller providing sequence, motion and process control. Analogue and digital command modules capable of controlling 256 axes of motion.

High-performance motion controller based on Mechatrolink II motion bus. The MP2300 is a compact, multi-axis machine controller that combines PLC sequencing and motion-control functions in one package.

Our All-In-One concept for Safety light curtains provides simplicity in mounting, configuring, daily use and maintenance. All devices include external device monitoring (EDM), interlock/start/restart and multiplex optical channels – all selectable. Also with common wiring and installation for all types. Easy configuration via built in dip-switches under a front cover Integrated alignment tool Finger or hand protection (14 or 30mm resolution) Max operating range 7m & 20m respectively Type 2 or type 4 according to EN 61496 Advanced models for muting and blanking

Versatile plug-in relay that sets the standard Since they were first introduced, over 500 million of these mini power relays have rolled off the production line. This truly versatile relay has become the standard, bringing enhanced features and flexibility for more user-friendly installation, commissioning and operation. 10A (DPDT) and 5A (4PDT) contact types, gold-clad contacts (MY4) Mechanical and LED indication Push-to-test button - momentary and lockable Labelling facility Hermetically sealed (MYH) and latching (MY2K) and PCB types available

Fully hermetically sealed relay is ideal for usage in hazardous locations. It is also available with bifurcated contacts. 4PDT contact type 3A rated load Class 1 Division 2 approval Bifurcated contacts available to achieve very low minimum switching current

Magnetic latching relay ideal for memory- and data-transmission circuits Double-winding latch system that holds residual magnetism. The special magnetic materials make changes due to aging negligible, thus ensuring long continuous holding time. There is little change in characteristics such as contact follow, contact pressure, etc. throughout its long life. Magnetic latching relay DPDT contact type 3A rated load Excellent vibration/shock resistance Built-in operation indicator ensures easy ON/OFF operation monitoring

Integrated HMI series. The NA-Series HMI is our next generation integrated machine interface as part of the Sysmac Platform. See Product Info

The Compact HMI series of easy to use and cost-effective HMI terminals available from 3.5 inch up to 10 inch sizes

The NC motion controllers have 4-axis point-to-point positioning controller with pulse train output. They support positioning control via pulse-train outputs. Positioning is performed using trapezoidal or S-curve acceleration and deceleration. Ideal for controlling simple positioning in stepper motors and servos with a pulse-train input.

NC is a common abbreviation for 'Normally Closed' often used to describe switches or contacts that are normalled closed until actuated.

16-axis point-to-point positioning controller over MechatroLink II motion bus. NCF is a powerful controller for point-to-point applications. It is based on MechatroLink II motion bus, which reduces programming and development and maintenance costs. Supports PLC Open Function Blocks.

The NE1A hosts the safety application program. All local and DeviceNet safety-based in- and outputs are monitored and controlled by the NE1A. It manages up to 16 DeviceNet safety slaves and can be seamlessly integrated in a standard DeviceNet system. Removable cage-clamp terminals for easy installation Predefined and certified function blocks for easy programming LED display and status LEDs for advanced diagnostics System status on DeviceNet for easy troubleshooting and predictive maintenance Easy scalability through the addition of DeviceNet safety devices

Scalable Machine Controller with logic, sequence and motion features for controlling 4 to 64 axis at up to 500µs. For more information see Product page on our Sales website.

The NL limit touch switch is available with a built-in antenna or with a separate antenna. Operation monitoring is easy using the built-in LED indicator. Switch activates when the actuator comes into contact with the object Detects minute displacement or lightweight objects with minimal force Built-in LED indicator ensures easy operation monitoring DC type provides functions combined with the S3D2 sensor controller

HMI terminal range. See Product Info

This model offers 256 colours (32,768 for image data), two USB connections for downloading or printing and optional Ethernet, Controller Link and Video board connections. One great advantage with the NS is that you can make use of Omron unique Smart Active Parts (SAP) that save you time when configuring, commissioning and maintaining your machine. SAP are pre-programmed, pre-tested visualisation objects with embedded communication code, bringing 'drag and drop' simplicity to HMI design.

This model offers 256 colours (32,768 for image data), two USB connections for downloading or printing and optional Ethernet, Controller Link and Video board connections. One great advantage with the NS is that you can make use of Omron unique Smart Active Parts (SAP) that save you time when configuring, commissioning and maintaining your machine. SAP are pre-programmed, pre-tested visualisation objects with embedded communication code, bringing 'drag and drop' simplicity to HMI design.

This series consists of Monochrome models with 16 grey scales and STN/TFT models with up to 32,768 colours. It is equipped with a USB connection for project download/upload and the possibility to communicate over Ethernet. One great advantage with the NS is that you can make use of Omron unique Smart Active Parts (SAP) that save you time when configuring, commissioning and maintaining your machine. SAP are pre-programmed, pre-tested visualisation objects with embedded communication code, bringing 'drag and drop' simplicity to HMI design.

NS5 Handheld, suited for use in harsh conditions. The NS series has evolved into a mobile format. Based on the standard 5.7” STN color version, we can offer a handheld version of the NS series. Offering 10 Function keys for most used functions and with a protection degree of IP65 it is the product to use in harsh environment where freedom of movement is needed.

This model offers 256 colours (32,768 for image data), two USB connections for downloading or printing and optional Ethernet and video board interface. One great advantage with the NS is that you can make use of Omron unique Smart Active Parts (SAP) that save you time when configuring, commissioning and maintaining your machine. SAP are pre-programmed, pre-tested visualisation objects with embedded communication code, bringing 'drag and drop' simplicity to HMI design.

10" HMI combined with PLC and Network interface. This model features 256 colours (32,768 for image data), two USB connections for downloading or printing and optional Ethernet. The product is combined with a CJ1G-CPU 45H and a DeviceNet or Profibus interface fitted into a compact housing occupying less panel space than the separate products. The Sysmac One is completely transparent, so the PLC, network (including field devices) and HMI can be accessed via a single port. A great advantage when servicing your machine remotely.

This model features 256 colours (32,768 for image data), two USB connections for downloading or printing and optional Ethernet. The product is combined with a CJ1G-CPU 45H and a DeviceNet or Profibus interface fitted into a compact housing occupying less panel space than the separate products. The Sysmac One is completely transparent, so the PLC, network (including field devices) and HMI can be accessed via a single port. A great advantage when servicing your machine remotely.

5.7" colour TFT/STN HMI combined with PLC and Network interface. This model features 256 colours (TFT 32,768, STN 4,096 for image data), two USB connections for downloading or printing and optional Ethernet. The product is combined either with a CJ1G-CPU 45H or with a low-cost CJ1M-CPU13 PLC and a DeviceNet or Profibus interface. It is fitted into a compact housing occupying less panel space then the separate products. The Sysmac One is completely transparent, so the PLC, network (including field devices) and HMI can be accessed via a single port. A great advantage when servicing your machine remotely.

8.4" HMI combined with PLC and Network interface This model features 256 colours (32,768 for image data), two USB connections for downloading or printing and optional Ethernet. The product is combined either with a CJ1G-CPU 45H or with a low-cost CJ1M-CPU13 PLC and a DeviceNet or Profibus interface. It is fitted into a compact housing occupying less panel space than the separate products. The Sysmac One is completely transparent, so the PLC, network (including field devices) and HMI can be accessed via a single port. A great advantage when servicing your machine remotely.

The NT11 is a Function key HMI with four text lines that can each hold up to 20 characters. It has a parallel printer connection next to a serial port for connection to a PLC. It has a LED backlight that has a life expectancy of at least 50,000 hours.

Proven technology with outstanding reliability. The NT21 is a cost effective product that offers features like two serial ports and blue mode for the LCD. Large screen capacity. Import of I/O points from CX-Programmer.

HMI with two text lines, 6-20 F-keys and up to two serial ports. The NT2S is the smallest HMI that we can offer you. It is based on a 16 x 2 lines LCD display with 6 or 20 Function keys. It offers IP65 protection, an optional RTC and printer connection.

The NT3S is a very affordable touch screen that helps you upgrade your machine to a modern human machine interface. The small NT3S offers features such as multi-language and two serial ports with multi-protocol functionality. The availability of a RS422/485 port means no need for a converter.

The OPC foundation makes a multivendor data access specifiction. See more at http://opcfoundation.org/

Transforms a standard computer into a complete motion solution in a seamless integration with the computer facilitating the development of customised applications.

Integrating PC-based control with human-machine interface (HMI) technology. Computer software for machine operation. The DyaloX industrial PC is created specifically for 24/7 operation and sets new standards in reliability, even in the most demanding industrial environments.

A photoelectric sensor, or photoeye, is a device used to detect the presence of an object by using a light transmitter, often infrared, and a photoelectric receiver

The Point-to-Point Application Software is the Omron-Yaskawa dedicated solution for point-to-point positioning applications. Absolute or relative positioning is possible. It is the ideal solution for palletisers, transfer lines, positioning machines or cyclic feed rolls. Homing functionality On-the-fly position referencing 8 position memories Brake control Emergency stop sequence and over-travel limit switches Varispeed F7 supported inverter

PROFIBUS is an open industrial fieldbus network. The standard is owned and managed by PROFIBUS & PROFINET International (PI) for automation

The ZG2 Smart Sensor enables solving advanced profile measurements with highest accuracy in an easy way.

PROFINET is an open industrial fieldbus network built on ethernet technology. The standard is owned and managed by PROFIBUS & PROFINET International (PI) for automation

The Pump Sequencer Application Software is the Omron-Yaskawa dedicated solution for pump sequencer applications up to 2 auxiliary pumps. It is the ideal solution for water treatment installations, building HVAC and industrial pumping. Dedicated physical units, faults and alarms Control mode selection by macro: pressure, flow, temperature Modulated pump with advanced PID and automatic frequency drop and rise Pressure feedback signal from analogue input Automatic/manual emergency mode operation by pump override Varispeed E7 supported inverter

Backwards compatible with the C200H series, it offers the widest selection of I/O and special function units. High resolution, high speed analog data acquisition.

Backwards compatible with the C200H series, it offers the widest selection of I/O and special function units. High resolution, high speed analog data acquisition.

Radio-frequency identification (RFID) is the use of an object (typically referred to as an RFID tag) applied to or incorporated into a product, animal, or person for the purpose of identification and tracking using radio waves.

A rotary encoder, also called a shaft encoder, is an electro-mechanical device used to convert the angular position of a shaft or axle to an analog or digital code, making it an angle transducer. Choose the performance you need from Omron's portfolio of incremental and absolute encoders providing different resolutions, shaft diameters and connectivity options.

The result is improved heat transfer, dramatic reduction in motor size and the best quality and reliability worldwide. SmartStep motors from 50 to 800W and Sigma II motors from 0.5 to 55kW.

With the S8M your machine will be directly UL Class 2 compliant, maximum tripping current is 3,8A per channel (adjustable). This unit controls up to 4 circuits. On top of this you will get startup / shutdown –sequence control, display and alarm functions, like voltage, output current, runtime, and over temperature and external reset. These functions can be set by using the front buttons or with the free support tool software. These settings can be protected. 4 circuit protection up-to 4A per channel UL Class 2 (max. 3,8A) Emergency stop by external signal Optimize use of available power through Start-up sequence Maintenance Control

S8TS DC back-up to prevent 24 VDC outages due to power failures The S8T-DCBU-01 battery backup block supplies 24 VDC for a fixed period of time during AC input outages to considerably improve system reliability. Supplies 24 VDC for a long period of time during AC input outages For system reliability improvement Block power supply basic block is connected by the bus line connector Simple system configuration Alarms indicated on main unit and via alarm signal output

Prevents equipment stoppage, data loss and other problems resulting from momentary power failures. One S8TS-DCBU-02 buffer block provides a back-up time of 500 ms at an output current of 2.5 A. Can be wired to the 24 VDC output from any switch mode power supply. Connects to all Omron power supplies: S8TS, S8VS, S82J, S82K, S8VM, S8PE Connects to both single-phase and three-phase power supplies Connects to an S8TS power supply via an S8T-BUS03 bus line connector Parallel connection up to 4 units to increase back-up time and capacity Complies with Semi F47-0200 standard

Buffer block against momentary power failures Prevents equipment stoppage, data loss and other problems resulting from momentary power failures. One S8TS-DCBU-02 buffer block provides a back-up time of 500 ms at an output current of 2.5 A. Can be wired to the 24 VDC output from any switch mode power supply. Connects to all Omron power supplies: S8TS, S8VS, S82J, S82K, S8VM, S8PE Connects to both single-phase and three-phase power supplies Connects to an S8TS power supply via an S8T-BUS03 bus line connector Parallel connection up to 4 units to increase back-up time and capacity Complies with Semi F47-0200 standard

All models have the same height of only 84.5 mm. These ranges cover up-to 1,500 W. The output voltages are 5, 12, 15 or 24VDC. In this series we got standard types and versions with two alarms up-to 150 W models: one for short dip in the 24VDC supply, second one when the voltage gradually drops in time. The models form 300 W / 600 W / 1,500 W are equipped with an overload alarm function. Widest range in DC-output voltage (5V, 12V, 15V & 24V) & wattage (15 up-to 1,500W) LED indication power ON Transistor output & LED indication under-voltage alarm 1 & 2 or Power failure All models can be Din-rail mounted (except 1,500W) EMI Class B, UL Class 1 division 2, SEMI-F47 (200VAC input)

The S8VS is our standard industrial DIN-rail mounted power supply. It’s build to last for ever. The compact S8VS is built in a strong metal case (except the 60 W version) providing a very good dimension vs. output power ratio to optimize panel space usage. The range covers 4 models with wattage of 60, 120, 240 and 480 at 24 VDC. The range withstands high vibration and shocks. The S8VS are fan-less power supplies. S8VS models available from 60 to 480W at 24VDC, 4 models Wide input range from 85 to 264 VAC Very compact, robust housing Overload protection All necessary approval available including SEMI-F47-0200

S8VS micro is our range for small power use. It is available in 15 W and 30 W in the same small 22.5 mm housing. In these versions we are using a new technology which improve the heat dissipation very efficient, giving more power output in this slim housing, 30 W. Due to this technology you can mount the S8VS micro in any position without de-rating. The S8VS micro is available in three different output voltages 5, 12 and 24 VDC. Wide AC input range from 85 to 264 VAC Output power range 15 and 30 W at 5, 12 and 24 VDC Three mounting directions, standard din-rail, horizontal or facing horizontal Mounting directly onto panel no problem, any directions is okay UL Class 2 (15-30 W) and UL Class I div. 2 (15, 30 W); SEMI-F47-0200

If you use a power supply under heavy circumstances like high temperature for example it will be very difficult to estimate the life time of the power supply. With our S8VS-A power supply this will be solved due to our unique measurement of the condition of the capacitors. An output will warn you 0.5 year before estimate shut-down of the power supply. On top of this you get additional information like output voltage, output current, peak current etc. Range for 60, 90, 120, 180, 240 and 480 W at 24VDC Output signal / display information for ending life-time Display shows output values: voltage, current or peak current Wide input range from 85 to 264 VAC Under-voltage alarm except for 60 W only display All necessary approval available including SEMI-F47-0200

With our power supply with run time you can set-up a warning for additional maintenance. Not, only for the power supply, but as well for other sensitive parts in your machine/ application. To have this feature normally you need to buy and connect a separate time counter or other controller. The time setting is 1 Kh per step. On top of this you get additional information like output voltage, output current, peak current etc. Range for 60, 90, 120, 180, 240 and 480 W at 24 VDC Output signal / display information for ending run-time Display shows output values: voltage, current or peak current Wide input range from 85 to 264 VAC Under-voltage alarm except for 60 W only display All necessary approval available including SEMI-F47-0200

To make the compact power supply range complete we have our 3-phase S8VT series, which give you the best power-to-footprint ratio. The range exists of 4 models with wattage of 120, 240 480 and 960 W all at 24 VDC. The version is build in a very robust metal housing and all models are din-rail mounting. The input range cover 3 phase voltage input from 340 to 576 VAC and single phase DC input from 480 to 810 VDC. 5, 10, 20 and 40A; 24VDC output 3-phase input (340-576VAC) or 1-phase 480 to 810 VDCxx Compact design with best footprint on the market UL60950 (CSA22.2-60950), UL508 listing (CSA22.2-14) and CE Parallel & serial operation possible

A self contained HMI library object that includes scripting or macros to perform some intelligent behaviour

Drive-based solutions for distributed motion control. Products available for simple point to point applications to advanced e-cam solutions.

A servo drive is a special electric amplifier used to power electric servo motors. It monitors feedback signals from the motor and continually adjusts for deviation from expected behavior.

The GW linear servo motor’s moving coil has no iron content and is made of resin-moulded motor windings. The stationary magnet track is made of two nickelised steel plates with accurately placed rare-earth magnets on each side. Plug and play, automatic motor recognition by servo drive Lack of magnetic attraction force extends the life of linear guides Bearings will run more quietly due to the lack of attraction force Attraction cancellation allows the use of smaller linear bearings Velocity ripple is minimised due to zero-cogging nature of the design

The SGMAH servo motor series has a low-inertia design for extremely fast accelerations and short settling times. Sizes 30W to 750W, rated speed 3000 rpm Peak torque up to three times continuous torque during 3 seconds High-resolution serial encoder Automatic motor recognition by servo drive Absolute multiturn encoder solution

The SGMBH servo motor series has an internal permanent magnet (IPM) design, which reduces rotor inertia. These servo motors are well suited for highly dynamic, high-power applications such as hydraulic system replacement. Sizes from 22kW to 55kW, rated speed 1,500 rpm Peak torque can be maintained for up to 5 seconds High-resolution serial encoder Automatic motor recognition by servo drive Absolute multiturn encoder solution

The SGMGH servo motor series has a medium-inertia rotor and incorporates the segmented stator design, which dramatically reduces overall size. These servo motors are well suited for applications requiring optimised load matching. Sizes 0.45kW to 15kW, rated speed 1,500 rpm Peak torque can be maintained for up to 5 seconds High-resolution serial encoder Automatic motor recognition by servo drive Absolute multiturn encoder solution

The SGMPH servo motor series has a medium-inertia design with a flat profile providing the highest torque-per-length ratio available. These servo motors are well suited for applications requiring optimised load matching. Sizes 100W to 1,500W, rated speed 3,000 rpm The length is about half that of similarly rated motors Peak torque up to three times continuous torque during 3 seconds High-resolution serial encoder Automatic motor recognition by servo drive

The SGMSH servo motor series has a high torque-to-inertia ratio and incorporates the segmented stator design, which dramatically reduces overall size. These servo motors are well suited for high-cycle-rate applications. Sizes 1.0kW to 5.0kW, rated speed 3,000 rpm Peak torque up to three times continuous torque during 5 seconds High-resolution serial encoder Automatic motor recognition by servo drive Absolute multiturn encoder solution

The SGMUH servo motor series has a high torque-to-inertia ratio for high-cycle-rate applications. The SGMUH incorporates the segmented stator design, which dramatically reduces overall size. Sizes 1.0kW to 5.0kW, rated speed 6,000 rpm Peak torque up to three times continuous torque during 5 seconds High-resolution serial encoder Automatic motor recognition by servo drive

The SHL switch features a long life and high precision due to its built-in coil spring, housed in rigid zinc die-cast alloy casting. Its mechanical life expectancy is 10 million operations. Alternating contact Micro load and general load Switching/min = 30 Immersion-proof IP67 IEC, EN, UL

The Sigma II servo series was designed with ZERO compromise on quality, reliability or performance. The servo amplifiers are ultra-compact with pulse and analogue inputs as standard, plus an auto-tuning function. Plug-in option cards offer enhanced functionality such as indexing and complex motions such as cams, gears and linked axes.

Omron's SmartSlice I/O system is compact, intelligent and easy. When used with Omron's CS1/CJ1 DeviceNet master units it is plug-and-work, no configuration tool is required. By using built-in functions such as pre-scaling, totalising, differentiation and alarming in analog I/O units, PLC programming can be minimised. Preventive maintenance data can be accessed using CX-Integrator software, standard PLC function blocks or NS-series Smart Active Parts.

SmartStep is designed and engineered to provide you with an easy way to migrate from steppers to servos in minutes. It accepts pulse-train input, can be configured quickly via simple dip switches and has an on-line auto-tuning function. Thus, the SmartStep offers all the simplicity and cost-effectiveness of a stepper with the added advantages of the servo drive capability.

A solid state relay (SSR) is an electronic switch, which, unlike an electromechanical relay, contains no moving parts. The types of SSR are photo-coupled SSR, transformer-coupled SSR, and hybrid SSR.

Omron's unique CompoBus/S is the most efficient I/O bus for machine automation. With free topology and up to 500 m bus length in long-distance mode, it can be used as a remote I/O system. In high-speed mode (100 m max.) the guaranteed sub-millisecond cycle time makes it ideal for efficient machine control. Used with the compact CPM2C-S PLC as master, your machine control system will fit in the smallest spaces.

Rugged I/O units for field mounting. Omron's unique CompoBus/S is the most efficient I/O bus for machine automation. With free topology and up to 500 m bus length in long-distance mode, it can be used as a remote I/O system. In high-speed mode (100 m max.) the guaranteed sub-millisecond cycle time makes it ideal for efficient machine control. With IP67 slave modules distributed throughout the machine, the need for protective enclosures is minimised.

Open motion control platform that offers a soultion from simple positioning to advanced co-ordinated motion. They can be used as an independent motion controller in combination with popular PLC brands since they support Ethernet, Profibus and DeviceNet communication.

Software package for communication with controllers over serial, Ethernet and EthernetIP. Formerly called FINS Gateway.

One Machine Software package for Control, Motion, Vision and Safety configuration and programming. See the Product Page on our sales web site for more info.

Thin shape inductive sensor in compact plastic housing The TL-T features a 12mm thin housing for space saving direct wall mounting. 12 mm thin housing Direct side wall mounting for bracket-less installation Up to 3 kHz response frequency

Flat shape inductive sensor in compact plastic housing The TL-W family offers a wide range of block style inductive sensors for simple mounting on flat surfaces. With sensing distances from 1.5 mm to 20 mm the TL-W is the ideal solution for all standard applications. Front and side facing surface IP67 DC 2-wire and DC 3-wire models Sensing distances from 1.5 mm to 20 mm For thin shape sensor, see the TL-T.

Trajexia is Omron’s new motion platform that offers you the performance of a dedicated motion system, the ease of use you get from an automation specialist and the peace of mind you have from a global player. Trajexia puts you in full control to create the best machines today and… tomorrow.

The Traverse Application Software is the Omron-Yaskawa dedicated solution for textile-wire winding applications. Perfect wire lying during winding process Ensures perfect and smooth unwinding Easy to use Varispeed V7 supported inverter

This special-purpose switch offers high contact reliability at high ambient temperatures up to 400°C. It has up to 1A switching capacity. It incorporates a ceramic insulator, cobalt-alloy spring and special alloy contact, ensuring high contact reliability at high ambient temperatures. High-temperature basic switch Stable operation up to an ambient temperature of 400°C IP00

Thanks to the patented design of the V1000 series and modern manufacturing, it is built for a 10 year life-time without maintenance. The new features guarantee a 100% expectation match. And with a field failure rate of less than 1 in 10,000, the new V1000 series inverter will outperform all other inverters long after it has been implemented. Up to 15kW / 18.5kW Built-in filter Current vector control IM and PM motor control Embedded safety stop function Category 3 (EN954-1)

The V400-F achieves highest 2D Code reading performance on challenging materials and environmental conditions. In combination with the easy and intuitive usage, the V400-F makes the difference. Pressing the teach button once is sufficient, to automatically adjust the settings for light and filter. This enables V400-F to read any Code correctly, independent of the quality or changing environment. V400-F is a compact system, which is available with integrated lense and lighting or as C-Mount variant. Easy adjustment of parameters Accurate reading of Codes Direct print marks on any material Eliminate the effects of print quality and work piece changes

The V400-H combines highest reading performance and ease of operation for mobile applications. The built-in LCD monitor helps to target the right position for V400-H in order to read the code and to display the measurement result immediately. Thanks to the excellent reading performance, direct marked or strongly degraded codes can be identified. The read 2D code can be stored on SD card or exported to a PC for further processing. The V400-H supports the traceability of components in assembly lines, were fixed readers do not fit. Easy to use – Target, Touch & Go Build-in LCD monitor for immediate display of results Accurate – reading of direct print marks Variable field of view

Omron's V400-R1 is an easy to use multi-code reader for 1D and 2D codes. It is targeting to read the codes on paper and labels. 360° rotated codes can be inspected. The small and compact V400-R1 in its different variants allows a flexible and space saving installation. Accurate reading of Barcode and Data Matrix Easy adjustment of parameters 1.3 Mpixel CMOS image sensor Flexible installation: front and side view variants

The V500-R5 is a laser based barcode reader for high speed processes. It can read codes on labels in any industry for traceability of parts or packages. Compact design Easy installation & setup Strong reading performance

RFID system for use in various Semiconductor applications (FOUPS & pods) Semiconductor applications require special product features in terms of chemical resistance and protocol for Identification systems. Omron's V640 is able to provide both e.g. communication with standardized glass transponders from Texas Instruments and SECS I/II protocol as well. Conformity to related SEMI standards (SEMI E99, E4 and E5) Antenna dimensions conforming to SEMI E15.1 Reading/writing ability of glass multi-page transponders (TI) Noise measurement function for best antenna performance Serial Network connectivity (RS485) for operation of several controllers at the same time

The high speed RFID communication system from Omron based on 13,56MHz helps you realize fast identification processes with only 14ms of read time. FeRAM tags allow nearly unlimited read and write cycles, and can be combined with Fluoro plastic designed antennas for wet or chemical environments. High-speed communication with only 14 ms of read time FeRAM battery-less tags for nearly unlimited operation cycles Different tag shapes for various applications Cost-effective RFID system with versatile useful communication functions Fluoro plastic housed antennas for harsh operating conditions

Universal material handling and assembly RFID system The V680 RFID system is used to track & trace the internal material flow in assembly lines or material handling. The ISO15693 compliant, FCC, ARIB and CE approved system operates at 13.56 MHz and features high resistance tags for harsh environments. Compact tags for embedded mounting Easy-to-use ID mapping software Diagnostic function for easy setup

V7 IP65 provides you high protection for compact sensorless vector control inverter, giving you the opportunity of decentralize your drives application without any extra cabinet cost and thanks to his features, being independent from main control panel. High inverter protection - IP65 Built in filter Compact size High torque at low speed. 100% at 0.5Hz CASE (Customised application software) and PLC option board

Omron’s V700 is a high-performance RFID system that can track & trace or deliver important data on almost any kind of object in any industrial application. It provides fast, reliable contact-less read/write (R/W) communication, even when operating in the toughest environmental conditions. Long communication range Low-cost high-efficiency RFID system Small Compact Reader with integrated controller can be offered High temperature tags even up to 180 °C are available Free download of Demonstration Software for quick system setup

RFID system conforming to SEMI E15.1, E99 and SECS I/II V700 SEMI is perfect and reliably realizes your data management in wafer application areas. It is the right choice in terms of specially cleaned tags and standard transmission conformance. Antenna design according to specifications in SEMI E15.1 Compatibility with SECS interface specified in SEMI E4, E5 and E99 ID link unit allows the multiple operation of antennas without interferences Specially cleaned tags in purified water are available Link unit V700-L22 conforms to SEMI standard E99

The VB switch can be used for the sequential control of a variety of engineering machines and belt conveyor lines. Built-in oil filter shuts out oil and water. Has a head box with a tough head, ensuring high sealing performance Built-in oil filter shuts out oil and water Mechanical life of 5,000,000 operations Ground terminal models are approved by EN and IEC and bear the CE marking Immersion-proof IP67

VBScript is a Microsoft scripting language. It is a subset of the full Visual Basic and installed by the Windows Scripting Host, as used by Internet Explorer for client side scripting. For details see the Microsoft web site

A virtual private network (VPN) is a network that uses primarily public communication connection, e.g. the Internet, to provide remote access to a central network.

The Smart Laser Micrometers can measure edges, diameter or the position of objects. Accurate and stable results are delivered, independent of whether the surface is transparent, opaque or shiny. The ZX thru-beam systems have a flexible measurement distance and can be scaled to increase the measurement range.

The Winder Application Software is the Omron-Yaskawa dedicated solution for winding and unwinding applications providing a specific calculation of the torque reference and speed limit in torque control for rewinder inverter drives. It is the ideal solution for paper, textile, plastic and metal applications. Diameter compensation (with or without external sensor) can be applied Static and dynamic friction compensation Tension control by motor torque or real measurement Varispeed F7 supported inverter

A wide selection of models is available, including overtravel models with greater OT, lamp-equipped models for checking operation, low-temperature and heat-resistant models and micro-load models. Various plungers and levers are also available. Two-circuit limit switch Direct and pre-wiring Metal housing, immersion-proof IP67 Ground terminal models are approved by EN and IEC and bear the CE marking UL, CSA

Smoother movement in the head section of this two-circuit limit switch ensures that a mechanical life of 30,000,000 operations minimum is now a reality. Fluorescent indicators improve visibility when setting stroke zones. Improved resistance to abrasion, smoother movement in the head section Mechanical life of 30,000,000 operations minimum Wiring and replacement for maintenance purposes are easily done Fluorescent indicators improve visibility when setting stroke zones Immersion-proof IP67

X switches incorporate a small permanent magnet in the contact mechanism to deflect the arc to effectively extinguish it. These switches have the same shape and mounting procedure as the Z basic switches. General-purpose basic switch Direct-current switch with built-in magnetic blow-out IP00

Omron's Xpectia is defining a new class of vision systems: real colour sensing, high resolution, 3D functionality and intuitive user guidance combined, provides you pure simplicity, no matter how complex the inspection. True colour system: 16 million colours High resolution cameras: 2 million pixels 2D and 3D inspections Touch-screen for easy operation Industrial-PC platform

All-in-one servo drive and motion controller integrated If your application demands the highest accuracy, the shortest cycle time in the most compact size and the ability to connect to ProfiBus or CAN, then look no further than XtraDrive. Complex motions such as cams, gears and linked axes are also available.

Z basic switches provide a large switching capacity of 15A with very high repeat accuracy. They come in a wide range of variations in contact form for your selection: basic, split-contact, maintained-contact and adjustable-contact gap types. General-purpose basic switch A series of standard models for micro loads is available High-precision switching A wide range of variations in contact Drip-proof IP00/IP62

The ZC-_55 switch is a modified version of the Z basic switch as a built-in switch. The mounting pitch is the same. It requires less operating force than conventional limit switches. ZC-_55 is economical and has a long life expectancy. Metal housing Alternating contact Switching/min = 20 Immersion-proof IP67 UL, CSA and EN

With the choice of 4 different 10 I/O CPU units we fulfill all needed functionality to do all kind of control automation. Three of them (C1/C2/C4) are expandable up-to 34 I/O. The C3 has fixed 10 I/O. All DC models have analogue input and a high-speed counter input up to 150Hz. The C4 model is equipped with communication. DC input/supply units have analogue input + high speed counter The ZEN-10C4 has RS-485 communication Expansion available with relay output or transistor output ZEN-Kits the best choice to start!

With the ZEN-20 I/O you get in one unit 12 Inputs and 8 Outputs relays or transistor. Herewith you can do a lot of bigger scale automation whereas the 10 I/O versions are just to short of I/O’s. The 20 I/O unit is available in three different versions starting from C1 with LCD display, control/ program buttons, calendar and clock or C2 with LED status indication or C3 same as C1 but fixed I/O. ZEN-20C1/C2 expandable up to 44 I/Os ZEN DC units have analogue input 0-10 VDC DC models have as well high speed counter 150 Hz. Expansion available with relay output or transistor output

To enlarge your ZEN application we provide three different expansion units in only 35 mm width ZEN housing. All expansion units have standard 4 inputs and 4 outputs. You can add maximum 3 expansion units to one CPU. 4 inputs, 100 to 240VAC or 12 to 24VDC 4 outputs, either relays or transistors (only DC models) DIN-rail mounting H 90 x W 35 x D 56mm

The ZEN Power Supply has the same compact housing as our 10 I/O CPU units. With a current/wattage output of 1.3A/30W it covers enough power to supply the DC ZEN itself and the eventually used sensors. If needed parallel operation is possible. Output voltage 24VDC Output current 1.3A Capacity 30W Allows parallel operation H 90 x W 70 x D 56mm

The ZFV colour comes with the same intuitive user interface as the grey scale version. But by using the colour information in the image, it adds more security and reliability to your application. More sensor heads and communication options make it more versatile. Intuitive - "teach&go" user interface Live - LCD display for setup and live inspection feedback Versatile - 8 inspection tools included Scalable - Add controllers to add functionality Flexible - Adjustable working distance and area Get insight in the best sensors for machines that never fail

The ZFV proves that vision sensors can be "teach&go". Parameter settings are available at the touch of a button. A smart user interface allows intuitive configuration using a built-in colour monitor. In Run-mode, the display gives live feedback showing results and images in real time. Intuitive - "teach&go" user interface Live - LCD display for setup and live inspection feedback Versatile - Up to seven inspection tools included Scalable - Add controllers to add functionality Flexible - Adjustable working distance and area

The new ZFX-C15 bundles advanced functionality with an intuitive user interface. The 3.5” touch screen offers easy access to the ZFX-C15. Auto-adjustment functions guide the user to solve the vision application. The ZFX takes care about lighting, filtering, etc. and hides the complexity from the user. Easy vision – Intuitive teach & go user interfaces Live – Built-in LCD touch monitors for setup and immediate feedback Communication – Centralized setup & inspection via Ethernet Versatile – App. 20 tools, 32 inspections per image Simplicity – Auto-adjustment functions for easy image setup

The new ZFX-C25 maintains the concept of intuitive user guidance. It is the 2 camera version of the ZFX platform and is optimized for high speed applications. Additional measurement tools, such as a contour search can be easily setup using the touch screen and solve complex applications. Easy vision – intuitive teach & go user interfaces Live – built-in LCD touch monitors for setup and immediate feedback Communication – centralized setup & inspection via Ethernet Flexible – 1 or 2 cameras, colour or monochrome Performance – High speed & additional processing tools

Easy profile measurement - Teach & Go The ZG2 enables precise shape measurement on challenging materials and surfaces. An easy and intuitive user interface enables efficient installation, setup and operation. A built-in LCD monitor indicates the measurement result in real time. Easy-to-use - intuitive user interface Live - built-in LCD monitor for setup and immediate profile display Versatile - 18 measurement tools Accurate - 5 µm resolution (3 mm / 631 pixels) Wide profiles - up to 70 mm

Displacement Sensor. Smart ZS-HL sensor offers superb dynamic sensing range for all surfaces from black rubber to glass and mirror surfaces by simply scaling it to your needs. The ZS-HL is the enhanced variant of the ZS-L, applicable for longer measurement distances, and offers compatibility with sensor heads and accessories. Highest resolution and dynamic sensing range for all surfaces Modular and scalable platform concept for up to 9 sensors Easy to use, install and maintain for all user levels Fast response time of 110 µs Multi-tasking capability - Manages up to 4 measurement tools in one controller

Displacement Sensor. ZX-E offers the best solution for the accurate measurement of metallic objects. It is highly recommended in harsh environments such as automotive and metal working machines. High resolution of 1 µm High-speed response time of 150µs Easy sensor head replacement Modular platform concept for different sensing technologies Easy linearity adjustment for any metal

Width-Measuring Sensor. The new ZX-GT Smart laser micrometer complements Omron’s Smart Laser Measurement platform. ZX-GT is able to detect edges, measure diameters of objects and calculate precisely the position on all kind of materials. Based on CCD technology ZX-GT achieves high accuracy and speed under difficult environmental conditions. Transparent objects, reflective surfaces or different positions do not have an influence on the result. The PC Smart Monitor software helps to easily setup and configure the laser micrometer. High accuracy: 5 – 10µm All surfaces Long sensing distance: < 500 mm Line width up to 28mm Calculation unit for multiple heads

Displacement Sensor. Smart, fast and accurate Laser measurement sensor Smart ZX-L offers plug & measure technology for applications where high resolution and fast response time is required. A wide range of interchangeable sensor heads provides greater flexibility in solving most demanding applications. Small and light sensor heads for easy integration High speed response time of 150µs Easy sensor head replacement Scalability through a modular platform concept Multipoint measurement with up to 5 sensors

Displacement Sensor. ZX-T is ideal for applications where the target object may contain oil deposits or other micro-structures. In this case contact measurement is the most reliable way. Modular platform concept for different sensing technologies Air-retracting types for automated inspection Multipoint measurement with up to 8 sensors Pressing force alarm prevents malfunction Strong ball bearing structure assures long life time.